Question about Chamberlain Powerdrive PD422D 1/2 HP Security Plus Screw Drive Garage Door Opener

1 Answer

Chamberlin whisper drive 3800

When either remote is deployed nothing happens. When inside door switch is pressed unit clicks but door does not move.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 244 Answers

May be bad logic board. is trolley jammed?

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Multifunctional control panel will not work when i tried to synchronize door control and light bulb on garage door does not light up?


I'm not familiar with the whisper drive but I would start with the most obvious place for a problem. There are two units at teach side at the bottom of the door jam. They have to be lined up for the door to work. This is the most frequent problem I have found because they are close to the floor and can be bumped out of alignment. Check to see if one of them have been moved. Most of these little plastic units have a plastic locator pin in the top of the unit. these pins snap into the mounting bracket. If the unit has been bumped just move the pin until it snaps back into the bracket. I'm not a contractor but I have seen this happen a lot with friends and family. Ask the easy questions first. Is it plugged in? Is the breaker in the power panel tripped? Good luck

Apr 13, 2016 | Chamberlain 1/2-HP Whisper Drive Belt...

1 Answer

How come my Chamberlain whisper drive hd600 safety sensor does not turn on the lights in the motor unit when the sensor is tripped when walking past it? It used to?


WITH THE LIGHTS ON PRESS AND HOLS THE LIGHT BUTTON UNTIL THE LIGHTS GO OFF AND THEN BACK ON (ABOUT 10 SEC.) THIS WILL TURN THE FEATURE BACK ON.

HOPE THIS HELPS

STEVE

Aug 18, 2014 | Chamberlain 1/2-HP Whisper Drive Belt...

1 Answer

Chamberlain whisper drive bulbs keeps burning out


I had a similar problem on my Liftmaster units made by Chamberlin. I would leave the garage door open for hours during the day so our dog and children can enter the house through our garage and laundry room. Everytime they come into the garage the Light's would go on because of the safety sensors are "tripped" at the bottom of the garage door tracks.
I turned off this feature and my lights are lasting much longer now. Over 1year in fact. To turn off and on this feature, make sure the opener light is off, then Press and Hold the Light Switch on the Wall Control Until for about 10 seconds till the light goes off. This deactivates this sensor from turning the lights on, but does NOT deactivate the sensor for Stopping the door if something is under it. Safety is still preserved.
Additionally, my door opener would vibrate while operating, and need to be aligned - I did this and also prevented the bulbs from "shaking". As we know the light bulb filaments are brittle especially after some use - this I think also helped lengthen the life of my lights on the opener.

Jun 30, 2012 | Chamberlain 1/2-HP Whisper Drive Belt...

1 Answer

We have installed a chamberlain wireless keyless entry. The problem is that when our neighbors house uses their keyless entry our garage door opens without us using our code. We have checked this seveal...


We have a Chamberlain Whisper Drive Plus. The keyless entry stopped working, suddenly. I have changed the battery, not the problem. I cannot get it to work, and cannot get it to reprogram. The keypad lights up when buttons are pressed, but when I press "Enter" the whole keypad flashes for about 30 seconds and then just goes dark.

May 10, 2010 | Universal Garage Wireless Keyless Entry...

3 Answers

Security light will not work


You must have a three function wall switch. This means in addition to a button that opens and closes the door there are two other buttons on the same wall switch. One is marked LIGHT and the other is marked LOCK.

To have your lights come on automatically when you walk into an open garage you must START with the lights ON. To turn the feature on, turn the lights on manually with the wall switch, then press and hold the LIGHT button for about 10 seconds until the motor unit light bulbs flash. Now, if the light bulbs are on, manually turn them out and then walk out through the open door. The light bulbs should come on.

To disable this feature, start with the light bulbs OFF and everything else is the same.

Aug 12, 2009 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
Chamberlain Powerdrive PD422D 1/2 HP Security Plus Screw Drive Garage Door Opener Logo

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chamberlain Car Audio & Video Experts

Iron
Iron

Level 3 Expert

3018 Answers

yadayada
yadayada

Level 3 Expert

67912 Answers

Are you a Chamberlain Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...