Question about Dryers

1 Answer

Stuck start/cancel button

Hi,

I have a hotpoint CTD40 tumble dryer. My kids were playing with the dryer and ended up with the start/cancel button being stuck.

Please advise how I remove/disassemble the control panel from the main body of the dryer so I can fix the button

Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 525 Answers

I attempted to locate an answer to resolve the issue for you, but you have not provided me with enough information to access my service database. Please observe the TIP below, and post me back and I will be happy to assist you further. Should you require more extensive consultation to help resolve your complaint(s), you may contact me through our premium chat service.
Tip: Always provide the complete information provided on the manufacturers product information data tag, located on the unit, and not in the user’s manual. This will help you acquire a more accurate and expeditious response to your complaint.

Below is a link that will help you with parts and diagnostic procedures that are specifically tuned to your manufacturers data plate information.
http://www.repairclinic.com/0047_8.asp
If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"

Posted on Jun 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoptoint CDT40G condenser tumble dryer pump running no heat or movement


hi i have a ctd40 mine wouldent go a few years ago on the heater i had three stats on one of them there is a tiny hole i pushed a sewing needle in hole it reset the stat you can see if you look at bottom of stat it might be concave so pushing it out set it again dryer then worked pull plug first

Apr 29, 2013 | Hotpoint Dryers

1 Answer

No power to myctd80 dryer


if i remember rite ctd40 has three stats over heater 1 has pin hole in top push needle in hole to reset it and take needle out then try ive done this on sum

Apr 01, 2013 | Hotpoint Belt for CTD00P, CTD40, CTD80,...

1 Answer

Timer counts down too quickly


Possible there is fault in the timer unit . check for loose connections or loose joints to the unit, if not this needs a replacement.

Jan 12, 2013 | Hotpoint Belt for CTD00P, CTD40, CTD80,...

1 Answer

Faulty control board hotpoint ctd85


You can remove the panel and check for fault in the connectors and the line to the display, use a hair dryer to warm and dispel any moisture on the board and panel. If there is no result then the panel has to be replaced.
To remove click : control panel

Jul 26, 2012 | Hotpoint Belt for CTD00P, CTD40, CTD80,...

1 Answer

My door for a hotpoint ctd40 tumble drier wont stay closed. The spring latch seems ok but not holding dooe closed. Any ideas since it dont say anything in my manual about it and its 2 yrs old. cheers andy


Hi andy.

the fault is likely to be in the roller catch mechanism. Hotpoint have modified these. Part Number is C00257618.

It includes both door latch and catch.
If you have problems obtaining one please email me on: aardvark.repairs@btinternet.com or call me on 01733 307019

Regards
aardvark repairs

Nov 18, 2009 | Hotpoint Dryers

1 Answer

Hotpoint ctd40 t dryer. wont start just ticking.


do you hear anything running?,might have broken the belt or idler wheel,motor runs but no tumble,need to look inside,warning !! unplug ,high voltage.be carefull

Sep 22, 2009 | Dryers

1 Answer

Ctd40 not drying


hi have the same dryer , if you look at the back of the machine you will see a thin whiteish tube check that this in in the outlets properly
hope this helps

Jun 20, 2009 | Hotpoint TDC32 Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

yadayada
yadayada

Level 3 Expert

64286 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...