Question about Kitchen Ranges

Open Question

No igniter vgsu1616bss - Kitchen Ranges

Posted by on

  • Anonymous May 10, 2009

    No igniter and no overhead fan power

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oven,broiler won't light


The igniter is the most commonly defective part for a gas oven that won't turn on. The igniter has two main functions. First, the igniter draws electrical current through the oven safety valve to open it. Second, the igniter gets hot enough to glow and ignite the gas in the burner assembly. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat. To determine if the igniter is defective, observe the igniter when the oven is on. If the igniter glows for more than 90 seconds without igniting the gas flame, this indicates that the igniter is too weak to open the valve. If the igniter is weak, replace it. If the igniter does not glow at all, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it.
Kenmore Oven Won Turn on

Jan 20, 2016 | Kenmore Kitchen Ranges

1 Answer

Oven and broiler won't work surface burners ok


The igniter is the most commonly defective part for a gas oven that won't turn on. The igniter has two main functions. First, the igniter draws electrical current through the oven safety valve to open it. Second, the igniter gets hot enough to glow and ignite the gas in the burner assembly. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat. To determine if the igniter is defective, observe the igniter when the oven is on. If the igniter glows for more than 90 seconds without igniting the gas flame, this indicates that the igniter is too weak to open the valve. If the igniter is weak, replace it. If the igniter does not glow at all, use a multimeter to test the igniter for continuity. If the igniter does not have continuity, replace it.

Troubleshooting Why Your Gas Oven Won Ignite or Heat PartSelect com

Jan 20, 2016 | Kenmore Kitchen Ranges

1 Answer

Location of ignition control module 2001 cadilac deville


Ignition Coils/Modules
The electronic ignition system uses an individual ignition coil for each cylinder. There are two separate ignition module assemblies located in the camshaft cover of each cylinder bank. Each ignition module assembly contains an ignition control module and four ignition coils. Each ignition coil connects directly to a spark plug using a boot. This arrangement eliminates the need for secondary ignition wires. The ignition module assemblies receive power from a fused ignition feed. Both ignition module assemblies connect to chassis ground. A Reference Low and four ignition control (IC) circuits connect each ignition module assembly to the PCM. The PCM uses the individual IC circuits to control coil sequencing and spark timing for each ignition coil. The IC circuits transmit timing pulses from the PCM to the ignition control module to trigger the ignition coil and fire the spark plug. The PCM controls ignition system sequencing and timing events

Dec 05, 2015 | 2001 Cadillac DeVille

1 Answer

Ignition switch diagrams


12V CONSTANT YELLOW Ignition Harness
STARTER WHITE/PINK Ignition Harness
IGNITION RED/LT. GREEN Ignition Harness
ACCESSORY GRAY/YELLOW Ignition Harness
SECOND ACCESSORY BLACK/GREEN Ignition Harness
also this might be of some interest to you if you are having ignition switch problems just look up this FORD ignition switch recall
NHTSA recall number 96V-071).

Aug 04, 2014 | 1990 Ford Taurus

1 Answer

I have a 98 Chevy Malibu Ls and the ignition won't


Inspect the old ignition cycle which is out.Is there any problem noticed of Ignition cylinder getting worn out.
Because when issue of ignition not turning off,its faulty ignition lock cylinder or faulty ignition switch.I suggest re-inspect the new ignition cylinder.
For more help,click the help link mentioned below:----

Ignition Switch Will Not Turn Off?
http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

Kexus ignition switch replace


To troubleshoot these issue, for ignition switch replacing procedure:---
Click the link below:---


IGNITION SWITCH REPLACING

It depends on vehicle to vehicle. But it's not very difficult on mot of cars to replace ignition switch. Basic theory of replacing ignition switch is same for all car models. -----

To replace ignition switch on your vehicle, I suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.

-------------

Click the link below: ------

----------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-----------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

---------

These will help.

Thanks.

Dec 06, 2012 | 1993 Lexus Es 300

3 Answers

How to replace ignition switch


It depends on vehicle to vehicle.But its not very diffult on mot of cars to replace ignition switch.Basic theory of replacing ignition switch is same for all car models.:-----
To replace ignition switch on your vehicle,i suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.-------------Click the link below :----------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------


How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------
1995 Ford Taurus: Ignition switch not turning OFF? http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-----------
Ignition Switch Will Not Turn Off? http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
---------
These will help.
Thanks.


Nov 25, 2012 | Cars & Trucks

1 Answer

How do i change the coil


Ignition Coil Removal
  1. Disconnect fuel charging wiring connectors from ignition coil (12029) and radio ignition interference capacitor (18801) .
  1. Disconnect ignition wires by squeezing locking tabs and twisting while pulling upward. e941a97.gif
  2. Remove four ignition coil retaining screws and remove ignition coil and radio ignition interference capacitor . Save radio ignition interference capacitor for installation with ignition coil .
Installation
  1. Position ignition coil and radio ignition interference capacitor to ignition coil mounting bracket.
  1. Install retaining screws and tighten to 4.5-7.0 Nm (40-61 lb-in).
  1. Apply Silicone Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or equivalent meeting Ford specification ESE-M1C171-A to all ignition wire boots.
  1. Install each ignition wire connector to the proper terminal on the ignition coil . Make sure boots are fully seated.
  1. Connect fuel charging wiring (9D930) to the ignition coil and radio ignition interference capacitor .

May 10, 2010 | 1998 Ford Windstar

2 Answers

How do i put a coil in a 2001 jaguar s type


303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system.
---------------------------------------------------------------------------------------
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system
-----------------------------------------------------------------------------
v-8
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the bolts and the ignition coil cover.
7b000cd.gif
  1. Disconnect the electrical connector from each ignition coil.
a1d93dd.gif
  1. Remove the ignition coils.
    1. Remove the bolts.
    1. Remove the ignition coils.
------------------------------------------------
v-6

SECTION 303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the engine appearance cover.
  1. To access the RH bank ignition coils, remove the upper intake manifold. For additional information, refer to Section 303-01A .
  1. Disconnect the electrical connector from the ignition coils.
  1. Remove the bolts.
  1. Remove the ignition coils.
please rate as fixed if this helps.

Apr 28, 2009 | 2001 Jaguar S-Type

1 Answer

1991 Dodge Spirit ignition problem


The "SPRING-BACK" Action is Originated in the Ignition Switch itself (THE ELECTRICAL SWITCH) I think that is where you should Look. On these models, the ignition lock and ignition switch are removed as an assembly. Refer to IGNITION LOCK .
Disable airbag, refer to Air Bags and Seat Belts/Air Bags (Supplemental Restraint Systems)/Service and Repair . After procedure has been completed, rearm airbag system.

On these models, the ignition lock and ignition switch are removed as an assembly.
  1. Disconnect battery ground cable.
  2. Remove tilt lever.
  3. Remove three Torx column cover attaching screws, then the upper and lower column covers.
  4. Using tamper proof Torx bit tool No. 440-TX20H or equivalent, remove three ignition switch mounting screws.
  5. Carefully pull switch away from column. Release two connector locks on seven terminal wiring connector, then disconnect from ignition switch.
  6. Release connector lock on four terminal connector, then disconnect from ignition switch.
  7. Remove ignition lock from ignition switch as follows:
    1. With key inserted and switch in Lock position, use a small screwdriver to depress ignition lock retaining pin flush with lock cylinder surface.
    2. Rotate key clockwise to Off position. Ignition lock should now be unseated from ignition switch assembly. Do not attempt to remove ignition lock at this time.
    3. With ignition lock in unseated position (lock bezel approximately 1/8 inch above halo light ring), rotate key counterclockwise to Lock position, then remove key.
    4. Remove ignition lock from ignition switch.
  1. Reverse procedure to install, noting the following:
    1. Connect two wiring connectors to ignition switch. Ensure switch locking tabs are fully seated in connectors.
    2. Install ignition switch on steering column.
    3. On column shift models, shift lever must be in P position and park lock dowel pin on ignition switch assembly must engage with column park lock slider linkage.
    4. On all models, verify ignition switch is in Lock position (flag parallel with ignition switch terminals).
    5. Apply a dab of suitable grease to flag and pin, then position park lock link and slider to mid-travel.
    6. Position ignition switch against lock housing face. Ensure pin is inserted into park link contour slot.
    7. Install ignition switch retaining screws and torque to 12-22 lb-in .
    8. With ignition lock and switch in Lock position, insert ignition lock into ignition switch until it bottoms.
    9. Insert key, then while carefully pushing ignition lock toward ignition switch, turn key clockwise to Run position.
    10. Check for proper operation on ignition switch in all positions.

FOR PICTURES EMAIL ME AT MY NICKNAME HERE ON FIXYA @AOL.COM

Feb 12, 2009 | 1991 Dodge Spirit

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

paulcarew

Level 3 Expert

2364 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...