Question about Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Open Question

Bosch SHU43C02UC/17 Machine stopped i n mid-cycle. Machine will not start now?

Posted by on

  • chattie67 Aug 04, 2008

    mine is doing the same thing... acts like there is no power to it, but there is... after fiddling with it, it came on but then when i shut the door it quit again.

×

3 Suggested Answers

  • 1 Answer

SOURCE: Bosch SHU43C02UC/47

How to loose up the circulation pump

Posted on Nov 03, 2007


  • 1 Answer

SOURCE: Bosch dishwasher

We were told by Bosch to not use lemon scent. Use the original generic soap with NO sprakle or smell because the jet dry does the rest. Just let the soap be soap. Hopes this helps.

Posted on Feb 20, 2008

  • 3 Answers

SOURCE: Bosch Dishwasher model : SHV4313GB/17 The

I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the water drained, but no new, clean water came through the hot water pipe. The drain just kept running, but nothing else happened.

Here's what happened. Under the main chamber of the dishwasher, by three inches or more, is a white plastic tray. It sits almost at the floor, and it may not be obvious that it's a tray capable of holding water. The overflow water spilled into that tray, which in turn caused a float in the far left side of the tray to lift (the way a toilet float lifts when the water fills in a toilet tank) and shut off the water intake valve (like the toilet float shuts off the toilet water flow). So long as that valve is closed, your machine will not run.

STOP: disconnect power supply at this point for safety.

To see the white plastic tray and thereby fix the problem, you'll need to take off the BLACK TOE-KICK (attached on my unit by two star-head screws at its bottom) and, possibly , the OUTER PANEL OF THE DISHWASHER DOOR (in my case, a custom wood panel (attached by a few screws through the inner side of the door, two screws that are accessed by popping off little--smaller than a dime size--covers on the sides of the doors, and then the door panel lifts up and out). (I took the outer panel off, but I can't remember if I would have had to reach into the white tray without doing so.)

Once you do that, you can see the white plastic tray. It doesn't come out--at least not without removing the entire machine--so try this. You can take your fingers and feel over and into the tray. You'll probably feel the water--I did. Look at the far left of the tray with a flashlight. Back there you'll see a flat, round, 3-inch diameter piece of white plastic sitting at the bottom of the tray. To its center is a generally U-shaped lever looking device, which, at its far left end, is connected to a red stick pointing up into the machine. When water goes into the tray, the float rises, causing the U-shaped lever to rise, causing the red stick to raise, which (though I couldn't see it) causes an electrical signal to run to, and shut, the valve for your water intake.

I took paper towels, and then a narrowly cut sponge, to sop up the water in the tray. I then took my shop vac and, using it as a blower, blew what little water was left right out. You might be able to use a hair dryer, but first sop out what you can or it'll take forever. Once you've done that, put everything back together and plug your dishwasher back in. My buttons are at the top panel. To reset, hold down the two buttons marked for clear drain for three seconds and release. You should be able to start up then. It took 15 seconds before the water started to run, but it did and the machine works fine again.

Interesting note: The valve that stopped the water from flowing in automatically opened once I got the water out of the tray. You don't need to reset the valve.

Good luck.

Montpelier Man

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with my bosch wash mch


Check timer to insure the cycle is completing sometimes the vacuum sensing line gets plugged and cycle may not complete

Robert

Mar 04, 2015 | Bosch Washing Machines

1 Answer

It is a Bosch WFF2000. The programme stopped mid


circle at bottom right take it off there is a filter there remove it and look of obstructions.WATER WILL POURE OUT!

Jun 23, 2010 | Washing Machines

1 Answer

Bosch shu43c06uc-17. Our dishwasher turns off mid cycle, and now leaks from the bottom.


  1. open the bottom panel 2-4 screw
  2. take a flashlight and turn the machine on
  3. see where it come from
  4. if you need take the unit out a bit from the counter
  5. check it all around to find the sorce of the leak
  6. good luck its EZ :)

Nov 28, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

2 Answers

Bosch WFMC2100UC Washer stops in mid-cycle


Hi, it seems its about time to replace the motor carbon brushes.
Thanks

Aug 31, 2008 | Bosch WFMC2100UC Nexxt Essence Washer

1 Answer

No pressure during wash cycle


check capacitor on motor. possibly not turning at correct speed

Jun 05, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

Not finding what you are looking for?
Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

prem mathew

Level 3 Expert

662 Answers

bosch5

Level 2 Expert

157 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...