Question about Computers & Internet

1 Answer

Engineering drawing 1

How to care for drawing tools

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

There are certain software which you can go through and select according to your requirement..

here is the link to go:-

Posted on Jun 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have loss of power and when fan is turned on the idle drops killing the engine. What could be the culprit?

This seems to be pointing toward the alternator. When the fan is running, this can take a chunk of available current from the power supply. If possible, check the voltage across the battery when the engine is running. It should be up around 13.8 volts but doe this when you only have the engine running and no radio, fan or anything else switched on. If that's low, possibly 12 or lower, then the alternator needs either the connections checking for corrosion, the belt that it runs off tightening or replacing.

Nov 06, 2014 | 2004 Chevrolet TrailBlazer

3 Answers

I truck won't start and battery won't stay charged

You might have a current draw when everything is off.
With the positive battery lead disconnected you need to get an Ameter to measure what current is being drawn with everything turned off.

Oct 13, 2014 | 932W Digital Battery Monitor with 12-Volt...

1 Answer

Remove drawer

If it is metal the draw could be out of alignment, tap it with a hammer to realign the travel action. As draws jam if not run squarely as they are designed to. If needed, use a small wood block to protect the surface of the drawer. Do this by placing the block on the draw face and hitting the block to realign the draw. This method means any damage will be limited to the wood block. But be sure of the draws design as hitting the wrong area will just tighten the draw.

If the draw is metal and corroded it may have to be loosened with CRC lubricant first for a hours/days. Use the same technique, with the hammer if needed. [if the hammer is in the tool box, improvise] Talk to a hardware specilaist about the lubricant or go the CRC site to get the right type;

If it a wood or plastic tool box the same principles apply. Just swap soapy water for 'CRC' using a spray bottle on a plastic draw as a lubricant. For wood the best lubricant is powdered graphite.

If all else fails your local car mechanic or a tradesman should be able to help.

Nov 17, 2013 | Washing Machines

1 Answer

Broken camshaft on 24 hp motor

If you never made it before, the best thing is get a repair manual, very hard to give some instructions in writing, you need some, drawing or picture.

Mar 19, 2013 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

Acrobat 9 Select tool does not draw a rectangle around an image

You have a select text tool and a select object one. To draw a rectangle you need to open the annotation tool. You will have the choice to draw a rectangle, a polygon, a cloud or other forms.

Dec 19, 2011 | Adobe Acrobat 9 Pro Full Version Academic...

1 Answer

It starts easily enought, but won't stay running. stalls after a minute or so.

The most likely problems for this are:
1. Fuel lines have deteriorated and are drawing air instead of fuel. Carefully check the lines within the tank.
2. Carburetor may need to have a new diaphragm and general cleaning. For DIY an in expensive fix.
3. Exhaust systems on 2-cycle engines can have significant carbon build-up which can often be seen when removed. This will affect the back pressure and make the engine difficult to start or difficult to maintain running.

Sep 26, 2010 | Garden

1 Answer

1999 Jeep Grand Cherokee V8 Dual Air Intake

is this one of those cyclone cartridges you put in the intake hosing? if so then dont waste your money, the power gain off of one of these is not noticable and the fuel economy wont change enough to make a difference, the engine is gonna draw air in at whatever rate it will, the only way to change that is with forced air induction (ie turbo, supercharger, blower). these things only help to mix the fuel with the air a little better so you get a more even burn and less wet spray fuel making it into the cylinder. forced air induction works by changing the volumetric efficiency of your engine, say you have a 4L engine, running naturally aspirated in 1 cycle that 4L engine draws an average of 85% of that 4L, if you put on a turbo or blower or supercharger you make that engine draw in more than its 4L capacity so your 4L engine would be running at say 120% of that 4L, trying to compress that much more fuel/air mix is where you get all the extra power from. ill save the explanation of an intercooler for another day....

Feb 25, 2010 | 1999 Jeep Grand Cherokee

1 Answer


Go to and search for your model there. Campbell Hausfeld makes the Husky line for Home Depot. Sometimes they are limited runs on certain products and you will not find any information about those tools. Its worth a shot to contact Campbell Hausfeld to see if you can get a breakdown for your tool. They do have an email and phone contact on their website. The power tools phone number is 1-800-424-8936. Good luck.

Apr 20, 2009 | Air Tools & Compressors

3 Answers

My problem is that i cant find a way to put the engine belt on my car. The engine bracket is in the way so i just need help putting the belt on. Am i supposed to take the bracket off and then put the belt...

There are 2 types of engines that you need to remove two bolts from the the engine bracket. to be able to install the belt. remove the bolts . not to be confused with the nuts . In order to replace the belt. there are only 2 bolts. Then you pry the tensioner to loosen the belt. remove it and press the tensioner to install the new belt. it will create tension automatically. hen replace the bracket.

Nov 26, 2008 | 1996 Buick LeSabre

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides