WATER/ICE DIPENCER NOT WORKING AND LCD DISPLAY MALFUCTIONING. TOUCH PADS NOT RESPONDING AND DISPLAY STUCK ON FLUCTUATING DAYS AND MONTHS OF THE YEAR 2001!

First, confirm that the display is working. If the display is still working, try pressing some of the touch-pad buttons. If some of the buttons respond correctly but others don't, it is likely that the touch-pad is at fault. (Some manufacturers sell the touch-pad separately from the control panel. Other manufacturers require that you purchase the touch-pad and control panel together. If you cannot replace the touch-pad individually, replace the touch-pad and control panel.) Frigidaire Dishwasher Lights Flashing or Blinking

You may have a bin switch which says the bin is full that is stuck

An EE error code means that you have loose connections (loose temperature sensor connections) check all the wires for a loose connection
temperature touch pad
the units main control board
the control board is in the back of the unit there is a panel covering in the middle lower back near the compressorInside your unit on the left side in the lower rear theres a vented piece of plastic pry that off thats the temperature sensor make sure all the connections are tight
If the error does not clear then your temperature sensor is faulty
you can get a new sensor at
www.repaiclinic.com.or
or at
www.appliancepartspros.com
hope this helped
Good Luck!

Your touch pad need to be replaced. I had the same problem and order a complete face lift which includes the touch pad from ebay. It was included aslo the special tools needed to remove the screws. There many videos showing how to desasemble the phone in youtube, just search with your model and you will find videos showing all the dtails how.
Please not that the problem is with touch pad which is the one you touch directly on it, is only vinil cover and is working as a keyboard. Under touch pad is located the lcd display of the phone which other part .

Just some general info on Danby Kegerators. The temp fluctuation is 32-42 degress thru out the day and for 1 hour a day you will get a temp of 46-48 degress during defrost. Unfortunatly there is no way to bring these coolers colder than 32 degrees.These Keg coolers need to be in a temp controled enviroment and if it is enclosed in a cabinet you need to have 3" opening on all sides for air to circulate. Some of the main fault codes are EE = open sensor and LE = which is a communication error between the display board and the main board. The LE error may be in the touch pad which gets moisture in the membrane and causes the pad to quit responded sometimes the error can be solved by simply disconnecting the molex plugs from the boards, straighting out the pins and reinstalling

Sound very much like your LCD inverter might be going luckily there pretty cheap and you should be able to find one on Ebay.

An LCD (liquid-crystal display) inverter is a component in laptop computers that supplies the power to provide a backlight to the monitor, enabling the user to view what's on the screen. This component is commonly the culprit when the monitor goes out and can be moderately simple to replace.

dude thats it mate game over

Raise temperature to 17 degrees.

FO- the touch pad is faulty. replace the eoc(electronic oven control)

I found it on the manual, it was in programming section!

Date/Time
NOTE: Time set on handset will be transferred to the base unit automatically.
1. Make sure your phone is OFF (not in talk mode).
2. Press the menu button to go to the main menu and use cid/vol (3or4) button to scroll to Date/Time.
3. Press menu button to enter the menu. Year 2006 shows in the display.
4. Use the touch-tone pad to enter the last two digits of the current year (range: 00 to 99).
5. Press menu button to save the year setting and proceed to date setting.
6. Date 01/01 shows in the display. Use the touch-tone pad to enter two digits for current month and day respectively.
7. Press menu button to save the month/date setting and proceed to time setting.
8. Time 12:01p shows in the display. Use the touch-tone pad to enter four digits for current time and use cid/vol (3or4) button to toggle between "p" (pm) and "a" (am).
9. Press menu button to save the setting. Saved shows in the display.
NOTE: If you subscribe to Caller ID service, the current date/time is set automatically when you receive your first CID record and will override manually set date/time.