Question about Samsung HLP4663W 46" Rear Projection HDTV

1 Answer

Can you help

My tv won't turn on, I have already replaced the ballast and the lamp. Well I checked the color wheel and it wasn't spinning when I push the power button. I checked and the color wheel is getting power.I removed the color wheel and when you spin it by hand it has a dry metal to metal sound, but it still spins freely.
Do you think the color wheel is the problem?
Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

Hello Brandon B
Great Job at trying to fix your own TV.....Bravo!! Ok, you may very well have a bad Color wheel. You have already change your Ballast and Lamp. The lamp would have been my first step. If you have a defective color this will surely cause the set not to come on. The DM board detects what going on with the color wheel and will not start the lamp. There are 2 types of color wheel listed for this TV.

List price $100
BP96-00674A COLOR WHEEL (FOR TYPE L3 VERSION PW03 UNITS)
Can you help - d6065dc.jpg
List price $100
BP96-01103A COLOR WHEEL FOR TYPE L6 VERSION PU01 UNITS

Best regards
circuitcity

Posted on Jun 22, 2008

4 Suggested Answers

Slinteriors
  • 8617 Answers

SOURCE: I need help with my DLP TV

If you have verified the votages are there at the color wheel and its not spinning the color wheel is most likely defective. the sound you hear when spinning by hand is most likely the bearing but that shouldnt stop it from spinning. but as i said if the supply voltage is present but it still wont spin. the color wheel must be defective.

Posted on Jun 20, 2008

  • 1 Answer

SOURCE: My DLP TV wont turn on.

As part of the power up sequence on the Samsung HLP-4336W the lamp isn't turned until timing pulses are detected from the color wheel. The color wheel motor is powered through the flat brown four conductor ribbon cable and the timing pulses are detected over the the three conductor ribbon table.

Posted on Jul 06, 2008

  • 31 Answers

SOURCE: TV will not turn on, Have three blinking lights, lamp won't turn on, color wheel isnt spinning.

the color wheel wil need to be replaced soon if it is doing that. it could be then DMD board as will.

Posted on Aug 14, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New member here. I have a 62" DLP Mitsubishi model #WD6252. I've already replaced my lamp AND ballast and continue to have the solid red lamp status indicator. I've made sure the connection from th


Your color wheel is failing or has failed. the red light ONLY means the lamp cannot light or was forced to shut down. it means nothing about the lamp or ballast specifically.

If your color wheel isnt spinning up correctly or you have a stuck fan somewhere, the lamp will be shut down immediately upon startup.

Id check to see if the color wheel is stuck or if its getting stuck.

Dec 17, 2014 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Samsung hln617w TV Dlp lamp won't turn on already replaced lamp, ballast, color wheel


It sounds like the main power supply has a bad capacitor. its a typical issue with a lot of electronic. look on the main power board that the outlet cord comes in to the TV and check all the cylindrical components for swelling, leakage, or singe makes.

Dec 13, 2013 | Samsung HLN617W 61" Rear Projection HDTV

1 Answer

I cleaned out my Samsung hl-s6187w and put everything back together and now it doesn't turn on. It makes a beeping noise like fast morse code and keeps cycling the power trying to turn on. The ballast gets...


Tv projection lamp inside the tv less than 2 years or so?Yes than the tv projection Lamp is good.You have this tv like 3 or 4 years already?The tv colors wheel even have been replace at leat once?No the tv probally require replacing the colors wheel these tv have to replaced the colors wheel every now and than.

Apr 14, 2011 | Samsung HL-S6187W 61 in. HDTV

2 Answers

Samsung hln617w dlp tv won't turn on. Red temp


Had similar problem. Thought it was the lamp. Examined old lamp but it appeared to be good. Ordered a new one anyway. Changed the lamp but the TV screen would not come on. It would make the usual noise as it was going to come on normally but it would cycle 3 times & then turn off. The LED lights in the front panel would indicate a defective lamp. Then read about the ballast. Changed the ballast & still same problem. Tried starting the TV without the lamp installed & noticed that the color wheel did not spin. Removed old color wheel & discovered it was broken. This appears to be the cause of all of my problems. I wish I new earlier of the test-turn on the TV without the lamp being installed & check to see if the color wheel is spinning. Would have save money on the lamp & ballast.

Apr 08, 2010 | Samsung HLN617W 61" Rear Projection HDTV

1 Answer

Lamp Light still on after replacement


First, A common mistake made is when you insert the orange ribbon cable from the Color Wheel into the DMD bd. To correctly insert the Ribbon Cable you need to look at both sides. You will see a shiny silver side and a dull black/orange side. You must insert the shiny silver side AWAY from the Color Wheel or towards the rear of the set. Now for the Ballast. When you power up the tv,Do you hear a short Buzzing sound? If you do that means that the Ballast is trying to fire up the Lamp and is working. Next, do you hear the Color Wheel spin up? If you do not then you have installed the Color Wheel incorrectly and you need to repeat the installation while making sure that you hold the rubber gasket in perfect place or else it won,t work. Chances are the gasket is in the wrong position and is binding the Glass Wheel. The Ballast is on the right side of the engine and on top of the Lamp Housing. You will see two RED High Voltage wires coming out of one end. Don't worry, there is no stored voltage in the ballast so you won't get a shock providing you have unplugged the tv from the outlet. That is the first step before you change any parts any way. Listen for the correct start sequence. With the rear backing off and the Safety Interlock Switch is being held in the up position, turn on the set. First sound you hear is a clicking which is the power on relay engageing. Then you will hear the fans turn on and then the Color Wheel spin up. Once the Color Wheel spins up and comes to full RPM then the Exciter on the Ballast will Buzz for less than half a second and then the Lamp should light up. Now if you have installed the correct Lamp and correctly installed the Color Wheel and you either are holding up the Interlock Switch or have reinstalled the rear cover and tightened all of the screws you should have a working tv.

Jul 12, 2009 | Samsung HL-R4266W 42" HDTV-Ready...

1 Answer

Heard a pop and now no picture


You are on the right track for the repair of the set.
You should be able to hear the color wheel spin up as the lamp begins to glow. If it is not spinning then that is the first thing I would replace. During the power on sequence, if the color wheel is not detected as spinning, the set will turn off the lamp.

Since the lamp is firing up, I would not suspect the ballast. I would say having a spare ballast and lamp is very good idea for these televisions.

I have repaired these sets before and have ended up replacing the lamp, ballast, and color wheel all at the same time.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up) If you cant rate this post with the highest rating, then please comment to this post and I will try to help you further.

Jun 12, 2009 | Samsung HLP4663W 46" Rear Projection HDTV

1 Answer

I need help with my DLP TV


If you have verified the votages are there at the color wheel and its not spinning the color wheel is most likely defective. the sound you hear when spinning by hand is most likely the bearing but that shouldnt stop it from spinning. but as i said if the supply voltage is present but it still wont spin. the color wheel must be defective.

Jun 20, 2008 | Samsung HLP4663W 46" Rear Projection HDTV

1 Answer

My DLP TV wont turn on.


As part of the power up sequence on the Samsung HLP-4336W the lamp isn't turned until timing pulses are detected from the color wheel. The color wheel motor is powered through the flat brown four conductor ribbon cable and the timing pulses are detected over the the three conductor ribbon table.

Jun 20, 2008 | Samsung HLP4663W 46" Rear Projection HDTV

1 Answer

TV will not turn on, Have three blinking lights, lamp won't turn on, color wheel isnt spinning.


the color wheel wil need to be replaced soon if it is doing that. it could be then DMD board as will.

Jun 20, 2008 | Samsung HLP4663W 46" Rear Projection HDTV

2 Answers

I need your help with my DLP TV


YOU PROBABLY NEED A DMD BOARD. THE COST OF THE BOARD IS $900 . YOU CAN GET A LIGHT ENGINE FOR $700 THAT HAS A NEW LAMP, COLOR WHEEL, BALLAST AND DMD.
WHAT A DEAL . THERE IS A $400 CORE ON IT SO YOU WILL HAVE TO SEND BACK YOUR NEW BALLAST AND LAMP TO GET THE CREDIT BACK.
WHEN I GIVE A QUOTE ON THESE SETS FOR REPAIR MOST OF THE TIME IT EXCEEDS THE VALUE OF GETTING A NEWER BETTER SET.
DON.

Jun 04, 2008 | Samsung HLP4663W 46" Rear Projection HDTV

Not finding what you are looking for?
Samsung HLP4663W 46" Rear Projection HDTV Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73086 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...