Question about GE 27831 Cordless Phone

1 Answer

The unit light doesnt light up, is it broken

I never used it have it like a year and when i pluged it in. It doesnt say its charging

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

You have to change a zenner diode inside of the base unit.

Posted on Jan 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not hold charge / shuts off


the batteries may need replacement. 2 aaa size ni-mh 560 mah 1.2 v are required. or the charger may be defective. If the charging light or the battery bars show up in display when placed in the cradle, the charger may not be defective.

Mar 16, 2015 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

My Panasonic KXTGA520M handsets, abt 8y. old, both cut out w/in 10 mins or so with no warning, yet their LCDs show "fully charged" and the base unit still works fine if I use it on speaker function.


These batteries only good for about 500 charges before they start to lose stamina .time to go to eBay and buy replacement batteries.they are around £6 -£8 .

Dec 06, 2014 | Panasonic Lands Phones

1 Answer

Hp dv7 laptop plug in but will not charge


broken wires inside the charging unit split it open after unpluging it of course and resolder the broken charge wires
then reseal the unit

Mar 04, 2014 | Lands Phones

1 Answer

Model ad583 ativa says check battery. Set is placed on charger,but does not charge,says:warning check batery! I did check battery,but no results. What's the problem? Needs new batteries?


I would tend to say if the unit is not holding a charge and the battery is connected correctly inside the phone, then the battery pack is bad. If the unit is heavily used and is a over a year old then it is possible the battery is bad. If the unit is newer, I would tend to lean with an issue with the base unit that would not be repairable.

Sep 12, 2011 | Office Depot Ativa D5772 Phone

1 Answer

Red light indicating fone charging has not shut off for around 20 hours.


My Vtech 6.0 charging light only turns off when I remove a handset from the charger base. I have had these three set for two years and they work fine. I think that the red light is just to let you know that the charger is working, if you loose power, or unplug one of the base units there is no indication of a dead battery.

Jun 11, 2011 | Vtech Cordless 6041 Phone

1 Answer

No dial tone both units


You have almost left no stone unturned. It is either a bad base station or a bad cord between the base and the jack. Try a new cord.

Jun 26, 2009 | GE 25840GE3 Cordless Phone

1 Answer

Installing a new base unit


You will need to press the page/locator button and hold it down until the charge light flashes. Once you do this, go to the handset and push OK. It should register as handset 4. Hope that helps. CG

May 17, 2008 | Panasonic KX-TG5632 Phone

1 Answer

Move closer to base


Either the phone is not registered to the base unit or the RF module is broken. It could be a bad battery but unlikely unless very old or you have not charged it. You should check the manual for registering the phone to the base unit.

Sep 07, 2007 | Panasonic KX-TG2584 Cordless Phone

1 Answer

Handset lights up, but does not work, only beeps when you touch any key


first, hold down the "handset locator" button on the base, until the "charge" light flashes. then, hold down the flash/call waiting button until the LCD says "handset registering." if after about a minute it says "error!!!" then try again. that is what the instuctional booklet says. i have not done this successfully yet as i have the same problem, but this is apparently how you fix it.

Jun 11, 2007 | Panasonic KX-TG2313 Cordless Phone

Not finding what you are looking for?
GE 27831 Cordless Phone Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Lands Phones Experts

kakima

Level 3 Expert

98816 Answers

Cindy Wells

Level 3 Expert

4805 Answers

Dudeman321

Level 2 Expert

230 Answers

Are you a GE Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...