Question about Xerox Phaser 7760/YDX Laser Printer

Open Question

Reseting the fuser for phaser 7760 - Xerox Phaser 7760/YDX Laser Printer

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: Xerox phaser 7760 streaking

to fined out what the problem could be you need to open a word doc and sent a blank page to the printer. from this it will show where the problem is in the printer
if u still get streaking it couls be a faulty toner and it may not be the cyan toner either. i would give the fuser unit in the printer a check. if there marks on tthis unit i can cause this problem as well

Posted on Nov 23, 2007

xptareq2000
  • 1447 Answers

SOURCE: Phaser 7760 - RAM ERROR

yes often your printer Ram or reset then solve it

Posted on Jun 26, 2009

  • 2072 Answers

SOURCE: Xerox Phaser 7760 Prints White Lines Diagonally Across Page

That is normally caused by a bad developer housing.

Posted on Jul 16, 2009

  • 1 Answer

SOURCE: i have blocked the fuser uit

All you have to do is open the fuser unit on the end (2 Screws) and you will find a fuse which has 3 strips (in a plastic casing with wires attached). You must the solder the strips so that they are joined, and that should reset the fuser.

Posted on Jan 13, 2010

  • 1 Answer

SOURCE: hello i hope someone can help me with my problem i

You can get more life out of the fuser by removing one end and placing a piece of tin foil OVER the THREE FUSES, which are designed to blow at set times. Just tape it in place with some tape.
Good Luck

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the fuser xerox 7760


NVM setting
  • 744-354 (Fuser Warning Point). Set it to 490.
  • 744-355 (Fuser Life Point). Set it to 500

Sep 15, 2014 | Xerox Phaser 7760/GX Laser Printer

1 Answer

Reset fuser on Xerox phaser 7760


You don't need to reset it it. It should automatically reset with no problem you can try to clear the NVRAM . Careful because you will lose all the information you have stored in it like any IP address or specific settings. What it will do is bring the printer to"factory default settings. You can do it in "service diagnostic mode. goodluck

Feb 19, 2014 | Xerox Corporation 7760/Dn - Xerox Phaser...

1 Answer

Xerox 7760 paper jam


at which position it will jam it matters tell in detail or send a sanp of it

Apr 10, 2013 | Xerox Phaser 7760/YDX Laser Printer

1 Answer

Xerox phaser 7760 saying "non-phaser imaging unit"


There is a snippet on the Xerox website to solve imaging unit recognition problems, link below. http://www.support.xerox.com/support/phaser-7760/downloads/engb.html?operatingSystem=winxp&fileLanguage=en_GB Usually this problem only occurs if the NVRAM has been reset or the engine board has been replaced without backing up the NVRAM. You can download the snippet to your printer through Centreware or by downloading the 'File Downloader' utility from the same page above.
Hope this helps.

Jan 09, 2011 | Xerox Phaser 7760DN Laser Printer

2 Answers

Hello i hope someone can help me with my problem i need reset the fuser uit xerox phaser 7760,because the rollers both(up,low) are like new condition thank you


You can get more life out of the fuser by removing one end and placing a piece of tin foil OVER the THREE FUSES, which are designed to blow at set times. Just tape it in place with some tape.
Good Luck

Oct 03, 2009 | Xerox Phaser 7760/YDX Laser Printer

1 Answer

I have blocked the fuser uit


All you have to do is open the fuser unit on the end (2 Screws) and you will find a fuse which has 3 strips (in a plastic casing with wires attached). You must the solder the strips so that they are joined, and that should reset the fuser.

May 20, 2009 | Xerox Phaser 7760/YDX Laser Printer

1 Answer

Xerox phaser 7760 streaking


to fined out what the problem could be you need to open a word doc and sent a blank page to the printer. from this it will show where the problem is in the printer
if u still get streaking it couls be a faulty toner and it may not be the cyan toner either. i would give the fuser unit in the printer a check. if there marks on tthis unit i can cause this problem as well

Nov 22, 2007 | Xerox Phaser 7700 Laser Printer

Not finding what you are looking for?
Xerox Phaser 7760/YDX Laser Printer Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Xeroxrep

Level 1 Expert

33 Answers

Philip Hughes

Level 2 Expert

68 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...