Question about Aiwa AV-D97 Receiver

Open Question

I have aAIWA AV D97 - AV receiver and it has the red light on but when i press the power button it wont turn on! It makes clicking sound ?

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 4234 Answers

SOURCE: Aiwa AV-D97 Power Issue. Just clcks when you hit the power button

The unit is most likely in protect mode. This means that the output section has a problem and the protection circuitry is preventing it from being turned on. This is to prevent further damage. The typical defective parts are the output transistors. Figure on $20-$40 for parts plus the local labor rate for repair.
Dan

Posted on Jun 10, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can i do to stop the red light blinking for marantz sr5007?


Turn off the power using X.
2 Press X ON/STANDBY while simultaneously pressing PRESET CH + and PRESET
CH -.
3 Once the display starts flashing at intervals of about 1 second, release the two
buttons

Aug 09, 2014 | Marantz SR5007 Home Theater AV Receiver

2 Answers

Denon 1312 makes clicking sound will not turn on


If the front display does not light up at all when the press the power button, it is usually either the main power fuse or the power transformer. If the fuse is blowing, that usually means a short in the amp section.

Dec 26, 2012 | Denon Avr-1312 Home Theater Av A/v...

1 Answer

When you press the power switch - power - only switch, the relay is opened again and the unit will not start.


check the secondary power supply the voltage regulator and the filter capacitor..i have encounte such prblem and found the filter capacitor is is leak almost shorted..hope it help

Apr 30, 2011 | Aiwa AV-D97 Receiver

1 Answer

What is wrong with my xbox it says error 65?


Error 65: DVD Drive Error.... DVD Timeout, Wrong firmware, dvd is without f/w chip, etc. This can also be caused by the tray not being fully closed on boot.

Flashing red:
1.the av cable cannot be detected
Make sure that the AV cable is correctly connected to the Xbox 360 console.
Disconnect the AV cable from the Xbox 360 console, and then reconnect the AV cable to the Xbox 360 console.
If the four flashing red lights continue to flash, try wiping the metal area of the AV pack with a dry cloth. The metal area is the end that plugs into the console. Wipe the metal area thoroughly, and then try the AV Pack again.
If the AV cable is correctly connected but the four red lights are still flashing, substitute a different AV cable if you have one available.
2.general hardware failure
Try restarting the console.
If restarting the console does not resolve the behavior, follow these steps:
Turn the console off.
Unplug all the power and AV cables from the console.
Unplug the power cord from the wall socket.
Firmly reconnect all the cables.
Turn on the console.
If these steps do not resolve the behavior, turn the console off, remove the hard drive, and then turn on the console. If the 3x Red LED error light is no longer displayed, turn the console off, re-attach the hard drive, and then turn on the console.
Also examine the lights on the power supply. When you turn on the console, the power supply light should illuminate green even if the three lights on the RoL flash red.

The specific type of hardware failure can be determined by a "hidden" error code
Turn the xbox 360 on, and wait till the 3 red lights are flashing.
Press and hold the sync up button (the small white one), while holding that button press the eject button.
The LEDs will now blink the first number in the code (as described below).
Release the eject button and press it again.
The LEDs will now blink the second number of the code.
Release the eject button and press it again.
The LEDs will now blink the third number of the code.
Release the eject button and press it again.
The LEDs will now blink the forth number of the code.
Release the eject button and press it again.
The LEDs will go back to the 3 red flashing lights.
You should be able to determine the difference between the 3 flashing lights and the error code lights by the rate in which they flash.

Here is how you interpret the LEDs to get the code number:
All four lights flashing - 0
One light flashing - 1
Two Lights flashing - 2
Three lights flashing - 3

0001 power supply problem
0002 Network Interface problem
0003 Power problem could be the PSU could be the GPU/CPU, somehow the console isn't getting clean power from the power supply.
0010 over heating
0011 over heating - If you are receiving this error after disassembling your console make sure to all 8 of the heatsync screws are tightened securely to the board/heatsink holes.
0012 over heating
0013 over heating
0021 DVD Drive Time out - Can be caused by problems with a firmware flash. This is also speculated to sometime be caused by a problem with the southbridge chipset on the motherboard.
0022 GPU Error / GPU Overheating

Feb 08, 2010 | Microsoft Xbox Console

1 Answer

No power


Does AV-D97 sounds click of relay when pressed power button?

Nov 03, 2008 | Aiwa AV-D97 Receiver

1 Answer

Aiwa AV-D97 Power Issue. Just clcks when you hit the power button


The unit is most likely in protect mode. This means that the output section has a problem and the protection circuitry is preventing it from being turned on. This is to prevent further damage. The typical defective parts are the output transistors. Figure on $20-$40 for parts plus the local labor rate for repair.
Dan

Jun 10, 2008 | Aiwa AV-D97 Receiver

3 Answers

Power on problem


Well this helped me find the relay but I found that after i pulled it off the board that it has some corosion around the metal prongs that hold it to the board. Could not get the relay open to do what is posted above , tryed opening it several times. Not sure if you are supposed to open it but could someone let me know. I am scraping around the prongs to get the corosion off hoping it will help but might just replace it alltogether. Further info on how to open the relay to do what is posted would help, I would appreciate any help, plzzzzz! :)

May 21, 2007 | Aiwa AV-S17 Receiver

2 Answers

Power on but no display


Hello Coach T, Reset Instructions: 1. If pressing the power button does not turn the unit off, unplug the unit, then plug it back in. 2. Press the power button while pressing the ENTER button. This will bring the unit back to factory defaults. Please let us know if you need any additional help. Best regards, nightdiver

Aug 21, 2006 | Aiwa AV-D57 Receiver

1 Answer

Subwoofer output


There could be a number of reasons causing this malfunction, try replacing the subwoofer's cord, it might be damaged, you can also try reseting the system to the factory settings according to the following instructions: Reset Instructions: 1. Press the power button to turn off the power 2. Press the power button while pressing the ENTER button. (note: this will reset all memory) Good Luck

Jan 09, 2006 | Aiwa AV-D57 Receiver

Not finding what you are looking for?
Aiwa AV-D97 Receiver Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aiwa Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5349 Answers

The Knight
The Knight

Level 3 Expert

75178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you an Aiwa Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...