Press ok without a remote control - Vizio L32 32 in. LCD HDTV

1. Scan the channels
   
   1. Press the Menu button on your remote control.
   2. Select Channel and press OK on your remote control. For Aerial you must choose the Cable option.
   3. Go to Auto tuning and press OK twice on your remote control.
      - Set the Automatic tuning screen to Cable (vertical) and Digital (horizontal). - Then press OK on your remote control.
   4. Enter the following values:- Search mode: Quick- Network: Manual- Network ID: the code for your region (22 for Flanders and 12 for Brussels)
   5. Press OK on your remote control.
   6. For Frequency enter the value 322000 and press OK on your remote control.
   7. For Modulation enter the value 256QAM and for Symbol rate enter the value 6875.
      Then select Search (or Next, this differs by type of TV) and press OK on your remote control.
   8. Your TV now scans the channels.

You probably can't. With the advent of newer, more sophisticated smart TVs, users need to think of the remote control in the same manner as they think of the controller for a video game console. Just as you can't play the video game without the controller, you can't watch the TV (at least not all functions) without the remote.

Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.

depends.....whats the type of tv and model? some tvs are fully remote controlled but if ya tv has a menu button press menu then press ok then select the options displayed by using the down arrowed button press ok go to search/tunig select auto tuning/search press ok it will select all channels automatically and store them press menu to exit

Hello
You can't unlock the V-Chip setting without entering into its service mode. This is actually a skilled work, and cannot be done without its remote control. If you have the remote control, entering into the s

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.
Then set volume to minimum and press "0" digit on the remote control to unlock V-Chip and to set a new password.
From this proceedings, you can know that, without its original remote control, the set cannot be unlocked. Try to get it from the nearest Duraband authorised service center or from any electronic spare part shops at your town. OK.
ervice mode do the following>

Hello
Sorry. Your TVs front panel has no menu button to press. The only way to chane it to AV/TV, cand be done with its remote control which ahs that button to press. You just buy one new remote control, of get the present one repaired. OK.

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................