Question about Coleman Powermate Powermate 5000W Generator

1 Answer

Im replacing engine on a model pm0525202 generator. i cant get armurature off shaft

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Coleman Master
  • 1,383 Answers

Assuming that you have removed the stator and the center bolt, (1) apply penetrating oil to space between engine shaft and armature and wait for a few minutes. (2) Then apply carb cleaner to same area and wait for a few minutes. Find a very hard piece of wood like ash or oak and place on metal part of armature and strike firmly with hammer first on one side then the other. If it does not come loose on first attempt start over from step one. The engine has tapered shaft that really holds on to armature. Huge heavy hammer will not help. What works is the vibration of the hammer blow. That is why you need hard wood. Good luck and be patient, let oil do its magic.

Posted on Nov 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for a schematic for a coleman PM0525202 generator?


rectifier not working replace it or gen is bad throw it away cost to much to fix

Aug 31, 2014 | Coleman Electrical Supplies

1 Answer

How do you seperate a kohler motor from generator on a miller welder?


if by asking this im assuming the generator is face bolted to motor , if this is so , to save from having another front bearing , the gen stator is directed attached to motor shaft , on the far end under end bell cover is the end of shaft , a long bolt goes thru gen shaft to screw into motor shaft , MARK/photograph all the wires you unhook helps a lot when puting back together

Aug 05, 2014 | Kohler Replacement Engine Part Pa-64711...

2 Answers

Engine runs fine but not putting out any power. thanks


Is the engine turning the shaft to the generator ? if it has a coupling device is it intact .. is there a reset button on gen output does it need reseting. or is it not working...

Apr 01, 2011 | Briggs Stratton Portable Generator 305cc...

1 Answer

It runs wide open all the time im wondering where idler arm setting is at


It sounds like the govenor spring has become disconnected or the clamp on the governor shaft has become loose and allowed the linkage to get out of adjustment. If problem has occurred suddenly it could mean the governor gear assembly inside the engine has broken and means the engine will need to be dismantrel to replace the governor gear assembly.
Check throttle linkage to see if spring is attached at both ends, one end on the throttle linkage and the other at the fixed point on the engine or to the end of the speed control lever. With engine stopped the spring should hold the throttle wide open and hand pressure on the linkage shoud be all that is needed to move throttle shaft closed to the idle position with no binding in the movement of the linkage.
If spring is OK and while engine is running, linkage should be able to be be moved to bring engine back to idle. If porblem has occurred gradually, then linkage will need re-adjusting. Loosen adjusting clamp on governor shaft, then holding linkage in wide open throttle position rotate shaft as far as it will go in the opposite direction to that requred to close throttle to idle . Re-tighten clamp.

Dec 11, 2010 | Coleman Powermate Premium Plus 6250W...

1 Answer

Connection of engine shaft to alternator


Shaft is tapered, alternator is forced onto the shaft when the alternator adapter plate is bolted to the engine.

May 05, 2010 | Electrical Supplies

1 Answer

You try and start it... it makes an initial start up sound..then all you hear is the starter..will not turn over


You need to replace the starter drive or the whole starter if you are not able to put the drive in yourself.another option is to take it to a starter repair shop and have them install a new drive.The drive is made up with a cog,a spline to travel up the armurature shaft with and a over running clutch,which allows it to get out of the ring gear after the engine starts.Over time the over running clutch will start "overrunning " on the way in to the ring gear as well as the way out and what you hear is the starter turning but the motor not,due to the slipping clutch in the drive.

Jan 20, 2010 | 2003 Volkswagen Jetta TDI

2 Answers

Coleman powermate generator


Put a small board(2x4 2x2 about 8 inches long)on the end of shaft and hit the board,it'll knock the shaft loose.

Mar 09, 2009 | Coleman Powermate Premium Plus 6250W...

Not finding what you are looking for?
Coleman Powermate Powermate 5000W Generator Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coleman Electrical Supplies Experts

John Trevino

Level 3 Expert

1383 Answers

Shawn DuRee

Level 3 Expert

355 Answers

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Are you a Coleman Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...