Question about Ace Hardware Ace & Electric Staple / Nail Gun

2 Answers

Have the Ace Hardware Electric Staple/Nail gun and have only used it to staple. Now I want to ust it to nail in brads and I don't have the manual or any clue as to where to load nails etc.. Please help.model # 2064673

Posted by on

  • apangilinan Nov 16, 2010

    This has been very frustrating to get an answer and by the time I do I won't need to use it but I will try again. I know how to load staples in my Ace Electric Stapler.Nail gun. How do I load and operate it with brads or nails?

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,740 Answers

I sure hate doing this but one of our experts wire12me did all the research on this and his post is here:
http://www.fixya.com/support/t1891738-stanley_tre550_need_know_use

Here is the graphic from hi shard work:
http://www.fixya.com/uploads/images/C901269.jpg

I tired to pull up the same graphic from the stanley, dewalt and black and decker sites with out any success.

The ACE 2064673 model is the same as the stanley model TRE550

The instructions in the first link above thanks to wire12me should get you going. Please at the bottom of his post click yes this was helpful. He deserves the credit.

Thanks for choosing FixYa,
Kelly

Posted on Nov 14, 2010

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

The best way to get the answer on how to load the nails on your gun, is to call your local ACE store or to call them at 1-866-290-5334. Sorry there is no manual on the link below.

Good Luck

Posted on Nov 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I load the stapler?


No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Jan 28, 2016 | Heavy Duty Stanley Bostich Heavy-duty...

1 Answer

Bt160hl stanly bostitch staple gun how do i load brads


I’m trying to buy brads, where can I buy the brads for this staple/Brad gun?

Jan 29, 2013 | Stanley TR250 H Heavy Duty Heavy Duty...

1 Answer

Problem with the Stanley Tools TRE550 Electric Staple/Brad Nail Gun Cannot get the staple drive flush help me please


First, try holding the stapler very firm to your project and make sure that the piece that you staple in to is backed solid with no give or springiness.
second, you might try shorter staples,or . . try dialing in more tension by turning the big knob on the back end that has the "+" "-"

Sep 11, 2011 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

How to load brads into stanley tre 550 electric staple/brad nail gun


HOW TO USE YOUR ELECTRIC STAPLER/NAILER
TO LOAD STAPLES

1. Unplug tool, (fig. 1)...(place on/off switch in "off" position, (fig. 2).)
2. Place on/off switch in "off' position.
3. Select proper staple length.
4. Use only staples identified by stock numbers on next page. Substitute staples may cause jamming.
5. Hold tool upside down. (Squeeze latch and pull, (fig.3).)
6. Drop staples in channel, legs facing upward. Push latch back in to lock in place, (fig. 4).

TO LOAD BRADS

1. Unplug tool, (fig. 1)...(place on/off switch in "off" position, (fig. 2).)
2. Use only brads identified by stock numbers on next page. Substitute brads will cause jamming.
3. Look for the image of a brad nail on the front side of the tool (fig. 5). Load brads into this side only.
4. Hold tool upside down (Squeeze latch and pull, (fig. 3).)
5. Drop brads into the channel, tilt the tool so the brads lay against the channel wall, (fig. 5).
Push the latch back in watching that the brad strip does not fall over.
6. Use High/Low power when driving brads.


TO STAPLE OR NAIL

1. Make sure the on/off switch is in the "off" position, plug stapling tacker in.
2. Turn tool on by switching to position 1 which is the "on" position and hold firmly against work surface to
engage safety mechanism.
3. Apply adequate pressure on the top of the knob (fig. 6.) while the trigger is pulled.

You can find the figures mentioned above at the following link:

http://bdk.force.com/FAQ/servlet/fileField?retURL=%2Fapex%2FPKB_Article%3Fid%3DkA0C0000000CdtPKAS%26brand%3DStanley%26returl%3D%252Fapex%252Fpkb_search%253Fbrand%253DStanley%2526mode%253D0%2526model%253D%2526sortby%253D0%2526terms%253DTRE550&entityId=ka0C0000000CdqqIAC&field=File_1__Body__s

Jun 20, 2011 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

I bought a used item #f509040 brad/staple gun (Air Ace) It came loaded with staples. How do I load nails??


The nails fit one side same place as the staples its usually on right side but may not matter. I hope this helps please rate if the answer helps in any way. Good Luck and have a great weekend.

Apr 03, 2010 | Ace Hardware Ace Staple Gun

1 Answer

How do you load nails into a stanley tre550 nail staple gun?


there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Dec 06, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Will only shoot one brad and then stops


its problem is too much oil or not enough. never the less, it needs taken apart and cleaned and inspected. make sure you are shooting the right guage and brand hardware. generic doesnt always work.

May 23, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Cant find replacement brads for swingline


the problem was not with a stapler it was with an electric brad nail gun made by swingline , after researching this, my swingline (printed right on the gun) turned into a "powerfast electric nailgun model 32003" which will take arrow replacement 1" brads .

May 04, 2009 | Staples Swingline® 36115 Staple Guns Tools...

Not finding what you are looking for?
Ace Hardware Ace & Electric Staple / Nail Gun  Logo

Related Topics:

1,120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ace Hardware Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

16147 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you an Ace Hardware Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...