Question about Ingersoll Rand - Rand 1/2" Impact Wrench, Quiet Tool with Extended Anvil

1 Answer

I have a IR 2130 Impactool 1/2 in drive I just got it used it seems to work ok but the torque seems to low I can hold it with my hand and it will not turn or take the lug nuts off the car is the torque adjustable or is the gun just bad

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

This gun shouldnt have an adjustment. If you cfm's from your compressor are enough. Too low cfm's mean lower torque. If cfm is high enough for the gun rating then I would say the gun is bad.

Posted on Nov 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

18 volt 1/2" drive impact loss torque


how old is the battery, test and recharge, if ok make sure is well oiled. May have to have it serviced if it is still low on torque.

May 20, 2015 | Dewalt Tools & Hardware - Others

1 Answer

How to repair IR 2130 air leak


http://www.ingersollrandproducts.com/am-en/support/manuals-and-technical-publications try this link, you can check the manual of your tool. I have taken mine apart and the only snap I had trouble it was the one way up in the handle. They do make a narrow long nose snap ring pliers.

Oct 13, 2014 | Ingersoll Rand Ir 2130 1/2 Heavy-duty Air...

1 Answer

I purchesed a BS18G Cordless Drill. How & when can I use the indication dial from 1 to 24 thank you


This dial is a torque setting. The higher the number, the higher the torque. Torque is a measure of how hard something is turned. For example, suppose you were using a regular screwdriver to tighten a screw. If you were to hold the screw driver loosely in your hand, your hand would slip before you tightened the screw very much. If you squeeze the screwdriver handle tightly, you could tighten the screw a lot more. The low numbers are like holding a screw driver loosely. The mechanism will slip before it tightens very much. This is only useful when you are trying not to overtighten small screws. When you are using it to drilll holes, you will want to set it at the maximum. Good luck, Al K

Apr 26, 2011 | Garden

2 Answers

In deep snow what mode do u drive in


under 35mph its normally recommended that you utilize 4 wheel low it is good for maximizing the torque needed to pull out of deep snow. Moderate-Aggresive Mud and Snow tires also work hand in hand. ~Daniel.

Dec 28, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Belt pulley bolts are working loose whats the torque specs


Seems like I answered this one before but I'll answer it again. The Fat Boy did not come with a belt drive primary from the factory. But, just in case you have a belt drive primary, the engine nut at the front primary drive torques to 150-165 foot pounds. The nut on the clutch torques to 60-80 foot pounds left handed. The large front final drive belt pulley torques to 125-150 foot pounds, left handed. You'll need a special tool to hold the front final drive belt pulley to prevent it from turning while applying the torque. Use locktite 271 red on all nuts.

On the front final drive belt pulley, take it off and look inside the pulley and inspect the small splines. If they're worn, the pulley needs to be replaced. Torquing instructions usually comes with the new pulley. They say torque the pulley to 50 foot pounds and then 1/2 hex or something like that. I've seen people have problems with this procedure. If you want to use this procedure, first torque the pulley to 100 foot pounds and then loosen the nut leaving the pulley where it is. Then, follow the instructions that come with the pulley. I've seen the pulley reach the 50 foot pounds of torque before it was fully back against the spacer giving a false torque reading. Needless to say, it will come loose if this happens. Good Luck

Mar 26, 2010 | 2003 Harley Davidson FLSTFI Fat Boy

1 Answer

Bought a used Toshiba model# 32A33 tv with vchip code set. Cannot reset. How can I reset vchip code?


Hold down the Vol - key on the TV. When Volume is at the minimum, hold down the 0 button on the remote. Remain holding both keys for at least 1 full second. Be sure your arm or hand is not obstructing the remote IR beam to the TVs IR receiver.

Mar 13, 2010 | Toshiba 32A33 32" TV

1 Answer

PTO clutch stop needs replacing 2130 Cub


take cover off flywheel so you can hold it from turning.or use a air compressor on clutch bolt

Jul 20, 2009 | Garden

2 Answers

REMOVE PARKING BRAKE ENGINE STALLS


i have a cub cadet 2130 2000 seris but it quits when i rekwase the brake pedal

May 03, 2009 | Oregon Scientific Oregon Gator Mulcher...

4 Answers

Toshiba Hdd/Dvd video recorder. Moved unit to a static caravan,comes on ok but when using the remote to use it ,no matter what button I press I get the message 1. DR-OFF Can you please help ?


Hold both the channel up and down buttons on the front of the recorder for 3 secs until DR1 shows in the display. Try it and let me know if it worked..

Apr 16, 2008 | Televison & Video

Not finding what you are looking for?
Ingersoll Rand - Rand 1/2" Impact Wrench, Quiet Tool with Extended Anvil Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ingersoll Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you an Ingersoll Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...