Question about Hifonics Titan TXi 6006 Car Audio Amplifier

Open Question

How do i get my hifonics amp out of protect mode?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: my Hifonics BX1500d is still going in protection

sorry, i am in the US. I couldnt begin to tell you where to get your amplifier repaired.

Try contacting HiFonics at www.maxxsonics.com


There are 3 possible conditions a HiFonics amplifier will go into protection -

Ground Loop - Blown or damaged speaker causing damaged Output FET.

Power Supply Failure - Blown Capacitors, Damaged FETs, Faulty Relays.

Thermal Shutdown - Excess Heat.

Mono channel amplifiers are the simplest to work on - and I would Estimate a repair cost of $75USD if it is a simple FET replacement.

Look at one hour of labor plus parts.

Hope this helped.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Mar 29, 2009

  • 13 Answers

SOURCE: hifonics brutus bxi 2008 amp. no power output

MAKE SURE SUBWOOFER OUTPUT ON YOUR RADIO IS ON IF NOT THAT COULD BE BAD INPUTS ON YOUR AMP

Posted on Aug 08, 2009

bigTROY502
  • 129 Answers

SOURCE: I got a hifonics brutus 2000w class d amp, it went

Either bad RCA's, Bad RCA ground from the radio, or blown suibs.

Posted on Aug 14, 2009

etirbynnor
  • 655 Answers

SOURCE: !!!red protect light is on!!!

Hello beaugarcia26,

Unless the amp itself is defective, there's a short or ground somewhere.

First disconnect the speaker wires and RCA (or high level) inputs, leaving just ground, remote turn-on and power leads connected. Then see if the amp powers up normally. If it doesn't check the ground with a multimeter and make sure it is good. If the amp powers up normally, check the speaker, speaker wires and inputs for shorts or grounds.

Hope this helps.

Posted on Sep 03, 2009

  • 396 Answers

SOURCE: i have a hifonics brutus 1206d and recently bought

there might be a losse hair in where the amp connects to all the wireing just take them all off and make shorter connectionts and screw it in tight

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hifonics bxi1210d amp goes to protect mode 2 seconds after turn on


Overdriving the output can cause it to go into protect mode. You will not be able to restore normal operation until failed components are replaced.

Jun 06, 2017 | Hifonics Car Audio & Video

1 Answer

Amp not working


sounds like the amp is going into protection mode. maybe a sub is shorted (blown). Or, the only other possibility is the mosfet transistors on the inside of the amp are blown.

Feb 01, 2010 | Hifonics Brutus BX 1205D Car Audio...

1 Answer

!!!red protect light is on!!!


Hello beaugarcia26,

Unless the amp itself is defective, there's a short or ground somewhere.

First disconnect the speaker wires and RCA (or high level) inputs, leaving just ground, remote turn-on and power leads connected. Then see if the amp powers up normally. If it doesn't check the ground with a multimeter and make sure it is good. If the amp powers up normally, check the speaker, speaker wires and inputs for shorts or grounds.

Hope this helps.

Sep 02, 2009 | Hifonics Brutus BX 1205D Car Audio...

1 Answer

Cant get protect mode off on amp


you burned up a couple of dioeds if if wnt go back to a regular mode

Apr 01, 2009 | Hifonics Brutus BX 1605D Car Audio...

1 Answer

Hifonics bxi2006d stays in protection


I am Maxxsonics distrubutor, they will not release the diagrams to anyone but they may sell you a new board. i have had 1 out of over 500 of the 2006 / 2008d amps do the same thing and they replaced the amp completely because they have so few extra repair parts for them (cuz they rarely fail)
here is their direct number just ask for Kellie and she will tell you what they can do for you.

1-847-540-7700

Dec 19, 2008 | Hifonics Brutus BXi 1206D Car Audio...

1 Answer

Okay i have a problem hifonics brutus 1500 mono d class amp


well your amplifier is obviously going into protect mode,(i used to have this amp and it is awesome) anyway i would go through just to be sure and check all the power connections with a test light, remote wire, positive, and ground. and check the fuse to see if it is still good. you can buy a test light at wal-mart and any automotive store. if you stil have a problem then i would check to see if your running below 1 ohm on this amp. that would cause it to go into protect mode. if all this fails i would just go buy a new one.

Oct 07, 2007 | Hifonics Brutus BX 1505D Car Audio...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hifonics Car Audio & Video Experts

Professor_V
Professor_V

Level 2 Expert

92 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Radames Pagan
Radames Pagan

Level 3 Expert

196 Answers

Are you a Hifonics Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...