Question about Heating & Cooling

1 Answer

LOW VOLTAGE WIRING CONNECTIONS BETWEEN NORDYNE FT4BF-0-36KA 16 SEER 3 TON HEAT PUMP AND B4VMX36KB\AH VAR 410A AIR HANDLER AND RITE TEMP 6036 THERMOSTAT. THE CONNECTIONS ON THE OUTSIDE UNIT ARE Y, R, O, C, W2IN, Y2, L, W2OUT. THE CONNECTIONS ON THE AIR HANDLER ARE Y1, W2, W1, O, Y/Y2, G, R, C. THE CONNECTIONS ON THE THERMOSTAT ARE C, B, O, W2, W1, Y1, Y2, RH, RC, G, A. ARE ANY OF THE TERMINALS ON EITHER THE AIR HANDLER OR THERMOSTAT JUMPERED TOGETHER AND IF SO WHICH ONES. I AWAIT YOUR RESPONSE REGARDS, GORDON

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Heating & Co... Master
  • 1,388 Answers

Jumper w1 and w2 at both tstat and ahu. That wire (white) should land on w2 outside.

Posted on May 15, 2017

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1796 Answers

SOURCE: LOW VOLTAGE WIRING CONNECTIONS BETWEEN

Hi!!
The Rite Temp thermostat can be wired many in ways according to your unit's needs, I would like to send you an installation guide showing the different configurations, then you tell me which and how many wires come from the heat pump and we go from there. For this I need an email address to send it to. Thanks

Posted on Nov 11, 2010

TheMobilian
  • 8220 Answers

SOURCE: LOW VOLTAGE WIRING CONNECTIONS BETWEEN

I guess you have not had the satisfactory answer you has been seeking since I been seeing this question all day.It is not surprising.
What you have is a heat pump.
It uses a compressor to heat and cool
This isnot an ordinary system. the unit uses a solenoid to reverse the flow of freon and needs a defrost mode, plus it requires backup heat. AND all of the wiring config ain't the same my nizzle.
This is just my take on it from what i know. I sold thermostats before i retired. heat pumps need specialty thermostats to not only cover the reversing valve but the back up heat and defrost features as well. that is why you only use the recommended wall thermostat for a designed heat pump. I thank you.

Posted on Nov 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the heat strips on a rheem classic 10 seer heat pump


3 Ton Heat Pump Split System ' eBay

www.ebay.com/bhp/3-ton-heat-pump-split-system
eBayGoodman 3 Ton 14 SEER Heat Pump Split System GSZ140361 with Installation Kit.10k Heat Strip,Thermostat,Wiring, Disconnect Box,Pad. $1,912.00; Buy It ...

Jul 28, 2015 | Heating & Cooling

2 Answers

What is the problem with running a 10 SEER condenser with a 13 SEER air handler other than efficiency? I had a 2 ton 13 SEER air handler installed last August to replace one about 27 years old. The...


as most ac units are capillary tube control not tx valve having matched units is critical. as for cost the condensing unit is much more complex and expensive than the evaporator.

Feb 14, 2015 | Amana Goodman R-410A Heat Pump Condenser 2...

1 Answer

What cause 3 amp fuse to keep blowing when power in turn on goodman air handler


The 3 amp fuse is in the red low voltage (24 volt) thermostat wire
and only gets power when the thermostat is set to turn on heat or a/c It should be connected to the red wire from the thermostat

Nov 13, 2014 | Goodman Manufacturing Goodman ARUF48D14...

1 Answer

I have a 1.5 ton air handler unit that keeps freezing. Ive blown the lines cleaned thw coils and replaced the filter.


If you have done all this then you need to have a tech come and top of the refrigerant, and if he doesn't see a leak, but you have a slow leak that happens over time it will freeze again.

Low level will cause the handler to freeze with other conditions, but it appears you have covered the rest.

Apr 12, 2013 | Goodman Manufacturing 1.5 Ton 13 SEER Air...

1 Answer

A/c shut off, I pulled T fitting and it worked, I drained water with wet vac, what else should I do?


Find out why you needed to wet vac the water.. It should drain overboard. Check for a plugged drain.

Feb 25, 2013 | Carrier Base 15 Series 4.0 ton 15.5 SEER...

2 Answers

I just installed strip heat Rheem RXBH-1724A10J 10KW 208/240/1/60 into Rheem 14AJM36A01, RHPNHM3624JC, 3 Ton 16 SEER Air Conditioner Split System W/ GE's Variable Speed thermostat Pro 701 and it ran up...


Hi,

This will help you.
guru_fixya_1.jpg

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

Jan 20, 2011 | Heating & Cooling

1 Answer

Is there a system mismatch with an American Standard 13 seer 3 ton compressor and a Nordyne 3.5 ton air handler? Noise at TRV when heating.


This must be a heat pump? Sometimes the unit can be more efficient with this combonation. What you are probably hearing is the reverse direction of the
refrigerant going back through the liquid line.

If in cooling sometimes you can hear a gurgling sound going through the expansion valve, sometimes
this is a sign of low refrigerant or the system is fine..

If you recently had the outdoor unit replaced and noise is an issue, check to see if the unit has isolation pads installed underneath the unit whether
it be on concrete slab or on brackets mounted to
house. Sometimes the new units come with compressor that has a jacket installed over it

Feb 14, 2010 | Ruud Central System Air Conditioner

1 Answer

3 amp fuse blows after three hours on Goodman 4 ton 16 seer pump


I would suspect you have a problem in the defrost circuit of your heat pump. there are a couple of things you can try. first just run the system on emergency heat and see what happens. you could have a defrost board that is shorting when it kicks into defrost. it sends a signal back to the furnace so it will come on during defrost. if you do not blow a fuse as long as you are running in emergency heat, i would suspect the defrost control board. also you could have a dead short in the wire that runs from the "w" terminal on furnace control board, out to the heat pump. keep in mind that any of the wires could be the cause and i am just tying to give you the most common things. your furnace will still run if you unhook all the low voltage wiring out at the heat pump. if you do this and stop blowing fuses. you know it is something on that wiring. goodl luck.

Jan 26, 2009 | Haier Energy Star ESA3183 Air Conditioner

1 Answer

1997 Amana 2 or 2.5 ton heat pump, 13 seer - air handler only blows 4-5 min


do you have a totaline t-stat. they and some other brands have a fan recirculation setting in the installers menu.

this is assuming that this happens in addition to the heating or cooling normally

Jul 02, 2008 | Amana PTH123B25AJ Heat Pump Air...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

2557 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...