Question about PDAs

1 Answer

Trying to figure out how to change attachment for a black and decker rtx 3 speed rotary rool

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The black and decker rtx uses the Flip-Lock spindle lock system for attachment changes. At the top of the tool there is a small rubber lever just above the on-off switch. Flip the lever down, and losen the grey collar surrounding the collet. Remove the collar and change the attachment. Then tighten the grey collar, and flip the lever back up. That's all there is to it!

Posted on Oct 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black Decker Manuals


Will any Black & Decker manual serve, or do you have a specific model in mind?

May 06, 2013 | PDAs

1 Answer

When i connect my usb and phone to the laptop the sign dosent coe


There can be following 3 problems.
1. USB driver on your laptop. If the driver on your laptop is not installed then it won't work. Confirm by putting any other usb peripheral.
2. USB cable is U/S. try change it.
3. Communication port on your mobile is U/S try to attach another mobile through same cable and check. If faulty then you have to replace the connector.

May 01, 2010 | LG KU990 Viewty

2 Answers

BLACK SCREEN · I TRIED TO RESTART MY PHONE AND NOW THE SCREEN IS ON BUT STAYS BLACK


I feel your pain. My g1 droped, the screen cracked, now 3 weeks later my screen turns black. Not even turning it off or removing the battery for hours changes this. However, i found if you wiggle the screen just right sometimes you can get your screen back... for a little bit.

Oct 17, 2009 | HTC G1

1 Answer

My braun multimix hand held mixer used to have several speeds and now only has one which is the forward hold all the time position. I opened it up and made sure the ball bearings were in place but no...


I just fixed mine. My daughter dropped it (again) and speeds 2 and 3 failed to work so I disassembled it and found a broken center terminal on the power transistor. I saw a fine crack so I soldered it. I also added much needed strain relief to the heat sink. It works fine now. This is a poor design. The power device has a heat sink attached and there is no strain relief so the transistor can move back and forth at least 3/8". For a tool that sees a lot of vibration and shock, this heat sink should be tie strapped or have hot melt glue to prevent movement. Gary

Nov 24, 2008 | PDAs

1 Answer

I have lost the instructions for my Black & Decker master vac, I have worked out how to use the blower but not the vacuum, can you help?


I don't have that model but usually there is a hole on the other side that you can plug the hose into for the blower. Hope that helps.

Jul 04, 2008 | PDAs

1 Answer

How to fill water in black decker steam iron


Hi there

Place your iron in an upright position like shown bellow
4f418cb.jpg
Take a jug of water from a kettle(Kettle water prevents blockage caused bu dirty water)
At the top of the iron you will find a hole
Pour the water into that hole and your iron is now ready for use!

Jun 27, 2008 | LG KU990 Viewty

1 Answer

Memory overload


Give this a try..
http://www.qusers.com/forum/viewtopic.php?p=67537

Mar 17, 2008 | Motorola Mobility Moto Q

1 Answer

Slow speed for GPRS


it seems you have a problem with the software not the hardware ,
try to use onther browsing program like opera mobile, if nothing help try to formating your device or install a new windows.

Dec 02, 2007 | i-mate JAM Pocket PC

Not finding what you are looking for?
PDAs Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top PDAs Experts

k24674

Level 3 Expert

7987 Answers

kakima

Level 3 Expert

96627 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...