Question about Snap-On 10 Snap-on Tools In Line Air Chisel Hammer W/2 Bits

1 Answer

I have lost my manual for my WB260A Wheel Balancer and need to Know how to recalibrate. Please send me calibration procedure.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to calibrate a snap on wheel balancer wb 260a

Posted on Jan 12, 2014

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I calibrate a Coats 700 tire balancer?

go to google --type in and there is a full operatots manual for that machine
you tube states that it is an auto calibrated machine
there is a calibration check procedure in the operators manual and again it states that the calibration is to fine tune for single spin operations.
I found this by typing into google---calibrating a coats 700 tyre balancer and there are pages which included the nytecsupply page.

Feb 07, 2015 | Cars & Trucks

1 Answer

Cannot recalibrate my Nuvi 50

Please see this link on how to recalibrate your touchscreen. The procedure should be the same as a Nuvi 14xx.

Mar 30, 2013 | Garmin StreetPilot C320 GPS Receiver

1 Answer

The screen touch point needs calibrated. If I touch a letter, it activates the letter to the left, etc.

Please see the calibration procedure here:

Please note that if you have to keep recalibrating the touchscreen, then that means it is drifting and needs to be replaced. More info on that here:

- Jim

Apr 24, 2011 | Garmin Nuvi 660 GPS Receiver

1 Answer


The manual for this should be at the bottom of this page.
The battery is just under a slide cover. You can zero it but to recalibrate you would have to send to a standards lab. The lab calibration would cost more than a new caliper so you really need to justify it. Basically if it is out of calibration just replace it, they are not really worth the money to recalibrate.

Apr 04, 2011 | Mitutoyo 500 171 20 Digital Caliper

1 Answer

The ligths of the air condition panel are blinkin.

It needs to be recalibrated. Likely because it failed the cool down test. Have you checked the freon level. After you fill the A/C it will have to be recalibrated. Check the freon and let me know. I'll post the calibration procedure if you need me to.

Apr 14, 2010 | 1999 Plymouth Voyager

1 Answer

We don't the manual for our model #BPA-440WGN and Serial #07091844 Blood Pressure Monitor. Believe it needs to be re-calibrated and don't know how to do that. It's consistently giving high blood pressure...

We're having consistently high readings with ours, too. We've compared it with as many as two other units at various test sessions.

From the manual:
All digital blood pressure monitors require recalibration in order to ensure continued accuracy.

This monitor does not require recalibration for 2 years under normal usage conditions (approx 3x/day), at which time your monitor will display "CA." The unit should also be recalibrated if the monitor sustains damage due to blunt force (such as dropping) or exposure to fluids or extreme hot or cold temperature changes.

To send monitor for recalibration, please ship to the address below with check or money order in the amount of $10 payable to HoMedics, Inc., for recalibration service, shipping and handling:

HoMedics Recalibration Service Center
Post Office Box 7050
Walled Lake, MI 48390

Allow up to 3 weeks for return of product. For additional information, contact HoMedics Consumer Relations at 1-800-466-3342.
So, do we spend $10 plus postage and wait 3 weeks or more...or do we use the $10 toward a new one immediately at a Walgreen's a half-mile away? It's a nice unit and works well otherwise, so it's a quandry. I hate to toss it. Good luck.

Mark in Oklahoma

Jan 29, 2010 | Walgreens Health & Beauty

1 Answer

I need to calibrate the coats 850 wheel balancer can u send me instruction on this

to calibrate coats 850, first you take a balanced wheel, tie it on machine shaft, enter the wheel dimension or wheel data such as distance, width and diameter, the press c90c, start the machine after completing cycle machine stops, add 100gm wieght out side the wheel and run it again, after this complete cycle your machine will be calibrate,
if you have any problem you can sent me email on
must reply me.
best regards

Jul 13, 2009 | Tools & Hardware - Others

2 Answers

Compass out of whack

You need to recalibrate the compass. The procedure is in your owners manual. Here are the basic steps.

First, you will need to verify that your compass zone is set to your current geographic location. Since I do not know where you are located, I cannot tell you the code. They are listed in the manual. (For example, So Cal is zone 5.)

Second, here is the compass calibration adjustment procedure:

Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
1. Start the vehicle.
2. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window.
3. Drive the vehicle slowly (less than 3 mph) in circles until CAL indicator turns off. As many as 5 complete circles may be required.
4. The compass is now calibrated.

Dec 19, 2008 | 2005 Ford F-150

1 Answer

Mono racing wheel

recalibrate it on the windows program, or download the logitech calibration program from their website, also make sure the pedals are properly connected to the wheel, if the connector is loose it might not work properly.

to recalibrate on windows - start - control panel - game controllers - logitech momo - properties - calibrate.

Nov 27, 2007 | Logitech Momo Force Racing Wheel PC

Not finding what you are looking for?
Snap-On 10 Snap-on Tools In Line Air Chisel Hammer W/2 Bits Logo

Related Topics:

1,409 people viewed this question

Ask a Question

Usually answered in minutes!

Top Snap-On Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1383 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

205 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Snap-On Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides