Question about Roper Dryers

1 Answer

Dryer not drying

My electric Roper dryer is about 2 years old. The heating element inside is heating, but the clothes do not dry. Air is coming out the vent hose very well. It's like inside the dryer is getting hot, but there is no air being ran to the inside of the dryer to dry clothes. It seems all the air is going straight out the hose. You can run the dryer 3-4 times, and still it will not dry clothes.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 210 Answers

Check your lint filter. Put it under running water to see if the water goes through it. Chances are it is clogged up. Wash it and put it back. Should do the trick.

SGt 48

Posted on Jun 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Roper elictric dryer is not drying clothes


If you are experiencing longer dry times and/or poor drying efficiency, the following link can give you some tihings to check before assuming there is a malfunction with your dryer:

http://www.fixya.com/support/r3578821-dryer_takes_too_long_to_dry

The number one cause of dryer heat related problems is poor exhaust ventilation. If not vented properly, a dryer will not dry efficiently, will take longer than required to dry, and will cause the heating circuits to overheat to the point of failure. The dryer will actually seem hotter as the heating circuits begin to overheat. This is also the source of many fire hazards if not resolved. Read through the link provided and review some of the potential causes. Hopefully, this may save you a service call. If you check everything and still have poor heating issues, please let me know. You may have an internal bias or hi-limit thermostat malfunctioning.

Jan 05, 2010 | Roper RES7646KQ Electric Dryer

1 Answer

There is no heat when dryer is on


you need chek :
if your apliance is gas dryer:
1-thermal fuse.
2-sensor flame.
3-ignitor.
4-gas valve.

if is electric dryer:
1-thermal fuse.
2-heater element.

Oct 05, 2009 | Dryers

1 Answer

Dryer has some heat but is taking a long time to dry clothes


This type of problem can be caused by a partially burnt heating element, a blown thermal fuse, or a faulty high limit thermostat. All of these components can be checked using an ohm meter or multimeter. Sure hope this helped and best wishes.

Jul 27, 2009 | Roper REX4634KQ Electric Dryer

1 Answer

My dryer takes 2 to 3 cycles to dry my clothes.


Check the following areas to combat this issue. in most cases, this will be a Venting issue.

1. Venting
Make sure the dryer vent hose, as well as the rest of the vent duct, is not clogged.

Unless regular maintenance is performed, chances are there is a lot of lint accumulated inside the dryer. This might affect the drying time and could be a fire hazard. Make sure to have your dryer cleaned regularly. Because this might involve taking most of the dryer apart, it is recommended to have a qualified appliance repairman perform this task.

2. Thermostat
There are a couple of cycling thermostats inside the dryer. If one of them breaks down, it might affect the dryer's performance. Replace the defective thermostat.

3. Heating element
A heating element might only be partially burned out, in which case it would still work but will take longer time to dry the clothes. Replace the element if found defective.

Jun 21, 2009 | Whirlpool LER4634J Electric Dryer

1 Answer

No heat


Check the following---


1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

May 29, 2009 | Whirlpool Dryers

1 Answer

Warm heat..clothes not drying


john there is only one heating element.ither it works or it dosent.when acustomer complains of low heat or long dry times 99out of100 its the venting or the dryer is blocked with lint.remove the dryer from the venting and try a load.if better clean house venting.you .........if not better you should have a great air flow leaving the dryer so if not drying well with venting off.take dryer apart a clean all araes that air is moving,where lint can block that flow.god bless .tom

Jan 01, 2009 | Roper REX3614KW Electric Dryer

1 Answer

Warm air but clothes not drying


Make sure u have seleced the high heat setting..The fact that it is heating more or less indicates that the element is o/k.
Check and clean any filter(s) that u can see,it is more likely to be a thermostat problem than anything else. and there are at least 2 of them, also check line voltage is correct.
Plz rate this solution.
thanks.

Jan 01, 2009 | Roper REX3614KW Electric Dryer

2 Answers

Dryer does not get hot enough to dry clothes Roper REX4634KQ1 Electric Dryer


Most common cause of this is a clogged venting going to the outside to test this remove the vent from the back of the dryer and run a load if it drys ok them you know you have a venting issue and will need to be cleaned out if not plz repost and we can look deeper into it

Jul 15, 2008 | Roper REX4634KQ Electric Dryer

3 Answers

Dryer does not get hot enough to dry clothes Roper REX4634KQ1 Electric Dryer


Either the heater element is breaking or is loose and getting only 110V instead of 240V.  First I would check the wall outlet with a voltmeter for 240V between Line1 and Line2.  Also check the connections and continuity for the heater element.

Oct 11, 2007 | Roper REX4634KQ Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Roper Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...