Question about Intel Motherboard

2 Answers

Repalced bad MS 7207 mobo with new one

I just replaced bad MS 7207 mobo with new one, but I have forgot where some of the connections go. They are a series of 3 2 pin connectors and the headers that go with them, but it is the headers that I am not sure of. One has a red and white wire to it, one has a white and black wire, and one has a white and green.
Thanks,
Brad Tway

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go here to see where the wires go...good luck!

http://support.gateway.com/s/MOTHERBD/MSI/105551/105551mvr13.shtml

Posted on Aug 13, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Near the CMOS battery in the Very corner are little leads sticking up out of the board. They should be color coded. That's if the mobo is a v2- otherwise check on MSI's site for a service manual.

Posted on Jun 19, 2008

4 Suggested Answers

tom19511
  • 1601 Answers

SOURCE: Front Panel Connection Problem

if you look at the PDF file here:
ftp://download.intel.com/support/motherboards/desktop/d845hv/A6513601.pdf
On page 68 you can see it more clearly. Just enlarge the file.
do you know the make and model of the case?

Posted on Nov 21, 2007

  • 1050 Answers

SOURCE: Intel Desktop Board #D850MV

Here is the tech sheet from Intel.
The front panel connections are listed on page 72, table 46. With options on the following pages.

http://support.intel.com/support/motherboards/desktop/d850mv/sb/cs-009907.htm

Posted on Aug 30, 2008

Dumaine
  • 112 Answers

SOURCE: Question I am not sure I know how or who to ask. I

http://downloadmirror.intel.com/15210/eng/D845GVSR_TechProdSpec.pdf


That is a link to the manual of the board...page 56 tells you which pin is which.....now for your case?? Well I have ran into that quite frequently.....and basically you will need to know where the wires are going to the front panel....I have had times where they were not even labeled at all and had to remove the front just to see where each wire went on the front

Posted on Aug 06, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I connect a ms-7207 ver:2.0 motherboard


http://www.manualslib.com/products/Msi-Ms-7207-697725.html

Sep 24, 2014 | Computers & Internet

1 Answer

MS-7297 Ver 2.1 Not booting: system fan not detected. I've bought in ebay a working msi mobo (so vendor says it works) that I can't boot because a message saying system fan not detected (bios...


you need the right heat sink for the cpu that you are using for the board check on board for cpu plug in, then plug the fan in make sure that you have enought heatsink paste on cpu not to much just enought to do the job. if that dose not do it then the board is bad.

Sep 24, 2013 | MSI Computers & Internet

1 Answer

What's your problem?MS-7207 VER:2.0 I TOOK THE 3 CONECTORS OFF AND DONT KNOW WHERE THEY GO BACK


Hello you can download a manual here:

http://www.msi.com/product/mb/645E-Max2.html#/?div=Manual

The pinout should look like this:



8_22_2012_2_20_15_pm.jpg

Its also printed in on the mainboard with very small letters.
Make the connection propely and the computer should start again.
Powersw goes to powerswitch etc.

Good luck

Aug 21, 2012 | MSI 645E Max2 (MS-6567) Motherboard

1 Answer

MS-7207 VER: 2.0


caut dravere pentru ms-7207 ver 2.0

Mar 05, 2012 | Computers & Internet

1 Answer

Need to know what wires go where for the power swith and lead lite and hard drive MS- 7207 Ver. 2.0


also known as the K8NGM2-L
manual online at MSI:
http://eu.msi.com/index.php?func=downloaddetail&type=manual&maincat_no=1&prod_no=224

Jan 07, 2010 | Intel Motherboard

1 Answer

I have vfd b 380v invertor some body repalced his


You will have to check your specs, some will and some won't.

Nov 19, 2009 | MSI Microstar KT6 Delta (MS-6590)...

2 Answers

The motherboard the shut down when switched on


Check heatsink/fan for CPU first. If this is Ok then try a new power supply.

Feb 02, 2009 | ASUS P5GZ-MX Motherboard

1 Answer

Consulta


Download here:

http://www.msi.com/product/mb/K8NGM2-FID--IL--L.html#/?div=Driver&os=All

One more with the same ms number:

http://www.msi.com/product/mb/K8NGM2-NBP.html#/?div=Driver&
os=All

Select your windows. Download the driver
Unzip the file before you install.

Good luck

Jan 02, 2009 | MSI K8NGM2-L Motherboard

2 Answers

MSI 7207 Motherboard (K8NGM2-L)


http://global.msi.com.tw/index.php?func=proddesc&prod_no=245&maincat_no=1&cat2_no=&cat3_no=

here it is...from here you ll take the manual,the configuration,the drivers and all the rest about your board..
fixya man:)
bye bye

Feb 09, 2008 | MSI K8NGM2-NBP Motherboard

Not finding what you are looking for?
Intel Motherboard Logo

Related Topics:

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intel Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2598 Answers

David
David

Level 3 Expert

753 Answers

Are you an Intel Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...