Question about Minolta EP1030/1030F CS/PRO Copier

1 Answer

Error code j3 for ep 1030 - Minolta EP1030/1030F CS/PRO Copier

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Minolta Expert
  • 231 Answers

J3 - exit jam
search for a lever at the exit point of the copier, you sould be able to see the sensor at the lower part of the fuser. I may bejamed or the flag broken.

Posted on Nov 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Minolta ep 1030 error e1


Imaging unit toner detection failure - during concentration read operation (F8), the result is less than 1v. Replace the developer and retry the F8 procedure.
---------------------------------------------------------------
Konica Minolta Error Codes & Solutions - http://www.kmcodes.com
Drum, Transfer Belt and Fusing Unit Firmware Reset - http://www.bizhubreset.com
Drum and Toner Chip Reset - http://www.chipreset.eu
Transfer Belt and Fusing Unit Reset Kit - http://www.resetkit.eu

Aug 18, 2014 | Konica Minolta Office Equipment & Supplies

2 Answers

What is Error Code E1 on a Minolta EP-2010


Sir/Mam,
Your ATDC sensor located in the developing unit or main board is bad. Have you recently had the developer replaced in the machine and did the person doing that use a vacuum cleaner to clean out the old developer if so then the static electricity form the vacuum cleaned destroyed the sensor. NEVER USE A VACUUM Cleaner to remove developer in the developer unit.

May 21, 2014 | Minolta Office Equipment & Supplies

1 Answer

My photo copier keeps saying pc ?


I worked on a EP 1030 copier and the error PC is when the machine doesn`t pickup paper. Make sure pickup roller is clean and there is paper in paper tray.

Mar 29, 2011 | Minolta EP1030/1030F CS/PRO Copier

1 Answer

I do not have drivers for matherboar EP-MF4-J3 for windows XP. Help me to be able to get that driver?


You can download all the Drivers for the Motherboard in your computer from the link below:

http://www.epox.com/downloads.asp?class=DRIVERS&item=EP-MF4-J3

Dec 20, 2010 | EPoX EP-MF4-J3 Motherboard

1 Answer

Driver download epox mf4 j3


http://www.epox.com/downloads.asp?class=DRIVERS

try to use (know the driver you need) box. If you still can not find the driver you want, find the chipset on the motherboard based on the media you like driverguide.com or you can try one by one driver with the chipset on your motherboard.

Jul 20, 2010 | EPoX EP-MF4-J3 Motherboard

1 Answer

C50 code on EP 1030


HI info
that code c50 is a fuser problem
the upper fusing roller needs to be replaced with the heating element with it inside of roller.

you will have to call a service rep, unless you are DO IT YOUR
Self
. Good luck

Nov 12, 2009 | Minolta EP1030/1030F CS/PRO Copier

1 Answer

My Minolta ep 1030 shows C04


Verify exposure lamp or  lamp's fuse.

Jan 14, 2009 | Minolta EP1030/1030F CS/PRO Copier

2 Answers

Minolta 1030


Depends if the lines go across the page as if the paper comes out or if they go down the page. If across then poss drum, transfer, or fuser unit, If down the page could be a short on the charge then poss only drum unit.

Thanks Jason

Aug 16, 2008 | Minolta EP1030/1030F CS/PRO Copier

1 Answer

Minolta ep 1030


It is not actually a paper jam - when the copier detects a malfunction, it simply stops everything. Paper jams all have "J" codes (J1, J3, etc.).

A CF3 indicates a problem with the ATDC system (Automatic Toner Density Control). The output from the ATDC sensor is outside normal specs.

Possible causes would include the copier being run (and reset repeatedly) without toner, the imaging unit not being properly installed (or not present at all), use of toner not compatible with the unit, a defective ATDC sensor or (least likely) PWB-A.

Jul 22, 2008 | Minolta EP1030/1030F CS/PRO Copier

1 Answer

Print head assembly on my Lexmark Optra S 1855 needs to be replaced. My question is what causes the print head to malfunction in the first place?


I guess you're getting an error message which is normally one of the below (causes underneath)

Error Code 931
No first HYSNC Signal
Error Code 932
Lost HYSNC =

These errors usually indicate a
failure in the HYSNC signal to the
printhead. Check the continuity of
the cables connected to J3 and J8
on the engine board. If incorrect,
replace the defective cable. The
voltage at J8-4 measures
approximately +5 V dc. If incorrect,
replace the engine board. The
voltage at J3-7 measures
approximately +24 V dc. If incorrect,
replace the engine board. If correct,
replace the printhead assembly.


Error Code 934
Mirror Motor Lost Lock
Error Code 935
Mirror Motor unable to
reach operating speed =

These error codes indicate a
problem with the mirror motor circuit
in the printhead assembly or the
mirror motor cable to the engine
board cable or engine board
assembly. Check the continuity of
the mirror motor cable connected to
J3 on the engine board. If incorrect,
replace the cable. The voltage at
J3-7 measures approximately
+24 V dc. If incorrect, replace the
engine board. If correct, replace the
FRUs in the following order:
engine board
printhead assembly

Jun 19, 2008 | Lexmark Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

633 people viewed this question

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6161 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

David Burkhart
David Burkhart

Level 2 Expert

210 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...