Question about Life Fitness 91Ti Treadmill

1 Answer

Once treadmill is turned on it starts then a couple seconds in it stops and says "start up error"

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 293 Answers

Hello,

It sounds like you have a reed switch malfunction. The reed switch is located next to the front drive roller at the drive pully under the motor hood. It is the little black wire with the pick up on the end. It need to be about an 1/8th of an inch away from the magnet that is mounted in the pully. If it looks lined up and is not twisted, check the other end. It is plugged into the controller on the other side. If all looks fine, you just might nee to get another one.

Hope this helps

Posted on Nov 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CardioZone SuperSportHR Club Fold-Away II ERROR 1


see the video and proceed according. God bless you



2) LUBE the rollers bearings too
3) test the drive belt motor, and replace it
4) Test the input voltage motor, if there are the motor need repair, see my personal TIPS for help
5) Test the output voltage board, for input voltage motor, if there are NOT THE board is faulty. see the block d.
God bless you
11_30_2012_6_42_10_pm.gif

Nov 29, 2012 | Cardiozone Supersport Hr Club Commercial...

1 Answer

I have A Life fitness 9100 treadmill The display shows the message "maintenance notes wax over" how can I remove this error?the treadmill will not turn on HELPPP


see this steps and fix it. .Of course you must read your instr. manual or download from www. iconservice.com
When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.

  • 2 Press the "ENTER" button three times to access the treadmill's error log.
  • 3 Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.
  • 4 To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.
  • 5 To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.
  • Oct 17, 2012 | Life Fitness Lifestride 9100 HRT...

    1 Answer

    Error Code E7


    To fix the error you have to put the safety key in start it it and wait for it to say E7. Now press stop and incline( up) together and hold for 20 seconds. Your treadmill will start to incline up. Take out your safety key. You just restarted your treadmill and can now put the safety key back and your problem will be fixed.

    Apr 22, 2012 | Exercise & Fitness

    3 Answers

    Hi, i have an Error signal " 2 - 9 F " the treadmill stops and cant run anymore. thanks a lot!


    I have a Matrix Treadmill t4. An error of "E1 and E3" occurs when it is started? Can you tell me the solution?

    Mar 15, 2011 | Matrix T3Xi Treadmill

    2 Answers

    Screen states Lube Belt , do not have user Manual , Where are lubrication points and what type "lube" can I use ?


    hi,


    It is necessary to lubricate your treadmill running deck every six months or 150 miles to maintain optimal performance. Once the treadmill reaches 150 miles, the console will display the message "LUBE" or "LUBE BELT". The treadmill will not operate while the message is showing. Hold Stop for 5 seconds to suspend message for 5 miles. Your treadmill came with a bottle of lubricant which can be used for two applications. If you need lubricant, contact Horizon Fitness. Only use lubricant provided by Horizon Fitness.

    • Turn off the treadmill with the on/off switch, then unplug the power

    cord at the wall outlet.

    • Loosen both the rear roller bolts. (For best results, place two removable

    marks on both sides of the frame and note roller position). Once the

    belt is loosened, take the bottle of lubricant and apply it to the entire

    top surface of the running deck. Tighten both rear roller bolts

    (matching up the marks for proper position) to original position. After

    you have applied lubricant, plug in the power cord, insert the safety

    key, start the treadmill and walk on the belt for two minutes to spread

    the lubricant.

    • Lubricate the air shocks with Teflon based spray.
    • Once lubrication is complete, reset the console by pressing and holding 'STOP' and Speed '+' buttons for 5 seconds.
    ok

    Dec 26, 2010 | Horizon T91 Treadmill

    1 Answer

    I have a horizon fitness t51 treadmill. I weigh about 138 pounds and typically run 5 miles a day at a 2% elevation at a steady speed somewhere between 5-6 mph. It recently has developed one of two...


    hi,
    from ur description i think ur treadmills control module have problem. motor driving card and motor is ok. normally there are no serviceable part inside the controlling module ( user interface module). only thing can do is remove the controlling module, take out its board check all the micro switches( press button switches) replace it found faulty or not( remember to remove the power before). the refix it and the test the tread mill.
    ok

    Dec 26, 2010 | Horizon Fitness Horizon Motor T51...

    2 Answers

    Message in the display "err 2" and my kettler treadmill doesn't work


    Hi Rendra,

    Try this:
    Switch the treadmill off and then on again.
    Push the "minus" speed button and the "stop" button simultanuously.

    If all is well you will now have entered the maintenance mode.

    Next push the "plus" speed button and the "stop"button smultanuously.
    Now you you've reached the error mode.

    Push the "plus" or "minus" speed button to browse the error codes untill you've reached "L er".
    The push start to erase the message.

    Turn the power off and then on again to restart the treadmill.

    With any luck the error has disappeared and the treadmill will function again. If not.....you'll have to contact Kettler.

    Btw...This error occurs when the belt is "pushed" by the runner. For example when you put weight on the handlebar and the push your feet backwards.

    May 10, 2009 | Exercise & Fitness

    Not finding what you are looking for?
    Life Fitness 91Ti Treadmill  Logo

    Related Topics:

    190 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Life Fitness Exercise & Fitness Experts

    Howard
    Howard

    Level 2 Expert

    115 Answers

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    6694 Answers

    Matt Olenzek
    Matt Olenzek

    Level 2 Expert

    293 Answers

    Are you a Life Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...