Question about Pramac Electrical Supplies

Open Question

I have a GSW 275 pramac generator.Display shows two warnings as W030 alto lıv combustıbıle and W055 Errata Sequanza Fası. What do they mean?How can I repair this generator?Are there any people who can repair it?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 474 Answers

SOURCE: need to change oil on my generator Pramac 16 hp

brigsandstratton.com

Posted on Oct 31, 2009

kel1guy2002
  • 3740 Answers

SOURCE: perkins 3 cylinder powered pramac generator

Start looking at your safety circuits.

1. High water temp
2. Low Oil
3. Low water etc...

From the manual these are the protection circuits.

• Engine protection: low oil pressure, high engine temperature.
• Genset protection: under/over voltage, overload, battery charger failure, battery voltage out of limits,
under/over frequency, start failure.
• Circuit breaker protection: IV poles.
• Differential protection.


Any one of them will trip the fuel relay closed. What you may be able to do is disconnect one at a time each protection circuit and see when the fuel relay opens. (Make sure to reconnect each one if it had no effect on the fuel solenoid)

Once you isolate which circuit it is in then you can chase wires or change the bad switch.

Thanks for choosing FixYa.

Kelly

Posted on Jun 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the name of the agent in Trinidad?


Aha, you mean the Pramac agent? There is not one in Trinidad, the nearest listed is in the Dominican Republic. See here

http://www.pramac.com/worldwide

.

May 04, 2016 | Pramac Electrical Supplies

1 Answer

Pramac any ideas why is my Pramac S12000 3 Phase Generator is only producing 26 volts. It was working fine at the full 400 yesterday. It is just over 2 years old but has only operated for about 40 hou


The first thing I would look for would be internal fuses blown. This sounds like a 460 volt 12,000 watt industrial generator and you probably should call the installing contractor for service. My 15,000 watt generator is over 30 years old and has less than 700 hours on it and those are mostly test-run hours.

Dec 13, 2014 | Pramac Electrical Supplies

1 Answer

Why my Pramac P9000 Generator does not start


Try a shot of starting fluid. If it does not start with that it may have a fuel supply problem.

May 14, 2014 | Pramac P6000s - 6000 Watt Portable...

1 Answer

How to change oil in pramac gsw 50kw towable generator?


If you have a Yanmar engine...
There is a hose that is connected to the oil pan in place of the drain plug directly under the oil filter that will have an end cap. This hose is used to drain the oil into a waste container.
Download the service manual located at the address below and follow the instructions in the manual.
http://www.martindiesel.com/Documents/New%20TNV%20DIRECT%20Service.pdf
Hope this helps.

Aug 21, 2013 | Pramac Electrical Supplies

1 Answer

Phase voltage is not same


What is your problem and what is the question?

Apr 16, 2013 | Pramac GSW120P-208 NA GSW Series 90000...

1 Answer

Wat is de klepspeling van een honda gc160 en hoe weet ik waneer ik de in laat of uitlaat klep kan stellen en wat voor olie moet er in


I have installed d530 sff mother board & processor is 3.0GHZ 800mhz error is showing.
Microcode update Error. Missing or Invalid processor microcode update. Please contact HP company.


D 530 SFF is support to 3.0 GHZ processor ?

Mar 02, 2011 | Pramac EG2800 T Handle Generator With...

2 Answers

Portable generator head stopped making power


portable generator head stoped making power engine runs fine sircut brakers are fine

Mar 16, 2010 | Pramac Electrical Supplies

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pramac Electrical Supplies Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Lawrence Oravetz

Level 3 Expert

9263 Answers

wadingriver
wadingriver

Level 3 Expert

2069 Answers

Are you a Pramac Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...