Question about Hotpoint Washing Machines

1 Answer

Replace a hotpoint tc71 dryer drive belt? - Hotpoint Washing Machines

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Its not so easy...

if you want i can explain in email

stevenmartin99@gmail.com

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My hotpoint aquarius ctd00 dryer won t spin when turned on but makes noise and heats up


We have made a few videos on these dryers and there are some very good repair guides on these.
How replace the bearing kit

And if you have the type with a fixed Riveted Drum shaft then you will need this video


In our repair guides you will find help on all the tumble dryer problems


How to Repair

Jun 26, 2012 | Hotpoint Aquarius WD63 Front Load...

1 Answer

How do i put a belt on hotpoint aquarius wf540


Afternoon,


I had a similar issue myself and I found the below link quite useful

http://www.buyspares.co.uk/how-to-change-a-washing-machine-drive-belt/advice-centre.pl?article=30


I also brought the belt off the site too and arrived next day - all in all I was a very happy customer, hopefully you will be also.

Feb 23, 2011 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Working but making noise when spinning.


  • Hi,
  • Try these:
  1. Balance the load
  2. Level the machine
  3. Inspect the water pump for a blockage
  4. Inspect the coupling
  5. Inspect the transmission
  6. Adjust the drive belt tension
  7. Check the motor bearings
  8. Check the drum brakes
please rate my suggestion....

May 19, 2009 | Hotpoint Aquarius WD63 Front Load...

2 Answers

Drum wont move


Check the motor and the belt on the back of the unit behind the rear plate. Make sure that the belt is attached and the motor is spinning. If this helped please rate. Thank you

Feb 12, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Need to replace drive belt on hotpoint wf430 but to tight to get


Put it on the motor spindle first then feed it onto pulley. It is tricky with such limited access.
Hope this helps &thanks for using Fixya.

Jan 22, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint wd420


your drive belt runs from the elec motorpully and then round the drum ?? so if yo look at the motor you will see it resembles rather like car alternator ?? and is fitted with a method of adjustment much the same ie a slide adjust bracket ? which you will slacken bolt/nut to enable motor to slide to a point enabling the fitting of belt? then with a suitable imlement? swing(lever )the motor till belt is taught and re tighten adjust bolt/nut also check the pivot mounting bolt/s/nuts are tight hope this helps

Oct 24, 2008 | Hotpoint Ultima WD72 Front Load...

2 Answers

Hotpoint wd64 washer dryer


mits86 , you are correct - it could be the belt.

REMEMBER TO UNPLUG BEFORE STARTING ANYTHING!

To do the belt...
1. UNPLUG the washer.
2. check you've unplugged.
3. Open the top of the machine - see the sides of the lid about 10 cm from front, remove plastic caps on each torx head, undo torx. (torx set required)
4. Remove concrete block from top - large spanner is required - remember the sequence so you can replace later.
5. Lean over the drum and see the large drive wheel.
If you see a broken belt then remove it and re-order one from hotpoint...see http://www.4hotpoint.co.uk/cgi-bin/product.pl?PID=634224&brand=&model=wd64&part=belt.

6. to replace belt - see motor shaft at bottom of unit. Dangle new belt round shaft of motor and gently pull so it does not come off motor.(This is not easy!)
7. At the same time Ease one side of the new belt back on to drive wheel on the back of the drum.
8. Turn Drive wheel until belt is on.(This is not easy and requires alot of hand strength)
9. Replace concrete block with bolt and spanner in reverse sequence you removed it.
10. replace lid, torx and cover for torx.

REMEMBER TO UNPLUG BEFORE STARTING ANYTHING!
- If the belt is not broken in your case - it could be the brushes on the motor - I can give you info on this if required!

Please dont forget to rate me as fixya.

Mar 07, 2008 | Hotpoint Aquarius WD63 Front Load...

3 Answers

Ultima Condensor Dryer


on the back of your dryer you have a heater behind the protruding panel... Either you heater element has gone, but most like the thermal cut outs have blown...these are located in the same area..they are small and round looking and are connected to them are wires either side. Anyways check the conitunity of the termal cut outs using a tester if no continuity then they are no good... hope it helps...

Nov 18, 2007 | Hotpoint Ultima WF860 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...