Question about Audio Technica Artist Series ATM410 Professional Microphone

1 Answer

How can i decode pin numbers? - Audio Technica Artist Series ATM410 Professional Microphone

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Pin 1 is connected to ground or shell
pin 2 is across from pin 1
pin 3 is in the middle between them
you can plug in a cable connector and see the numbers molded in it

Posted on Nov 30, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Heil icm plug wiring diagram

The Heil "ICM" microphone is designed to be used with certain Icom brand ham radios. These have a 8-pin round plug. Describing the pinout to you will depend upon your perspective, whether you are looking at it from the microphone plug itself, or the microphone socket on the front of the radio. Therefore, from the perspective of looking at the mic plug on the end of the mic cable, note that there is a notch or dimple in the plug that also lines up with the screw. Going clockwise from the notch, the pins are numbered 1 thru 7. Pin #8 is the center pin.
Pin 1 = mic input
Pin 5 = Push-to-talk (PTT)
Pin 6 = PTT ground
Pin 7= Mic ground

From the standpoint of an Icom transceiver, the remainder of the mic connector pins are as follows:
pin 2 = +8 volts DC (output from the radio)
pin 3 = frequency control up/down
pin 4 = squelch switch
pin 8 = audio output (level varies w/vol control)
Hope this helps

Jan 03, 2014 | Heil Sound Audio Players & Recorders

1 Answer

Find my p2r pin number: name Richardson

I don't understand your qeustion. Can you please provide more detail?

Oct 04, 2013 | Shure P2R Personal Monitor Hybrid Bodypack...

1 Answer

How do you wire ecm77 to jackplug

There are literally hundreds of styles and sizes of jacks and plugs. The ECM77 is a condenser microphone and REQUIRES phantom power to bias it. Not all body packs have this bias available...MOST current mixers do have phantom power, at least on XLR inputs. Since you did not tell us what this connects to, we can't give you a definitive answer.For an XLR, the shield of the cable will tie to pin #1... be careful as the pin numbers are tricky... Typically for a TRS 1/4 or 1/8 jack, the shield of the cable ties to the sleeve part of the plug and the other two wires to the tip and ring contacts.

Mar 13, 2013 | Sennheiser freePORT Wireless Instrument...

1 Answer

Whenever i hold my shure mic there is this humming sound coming out of my speaker

You have a bad cable or incorrectely wired cable. The cable should have XLR connectors both ends. Verify that like numbered pins are connected end to end. The shoeld lead on pin 1 of the connectors is probably broken at one end.

Sep 13, 2011 | Shure SM58 Professional Microphone

1 Answer

What are the true xlr connection numbers for bottom blue and red wires

Blue wire connects to XLR pin 2.
Red wire connects to XLR pin 3.
You can find a wiring diagram on Shure's website.

Apr 19, 2011 | Shure SM58 Professional Microphone

1 Answer

My se x1 condenser mic has starting to cut out, usually just for a second and it seems to be when louder noise goes through it (though this is not too loud as its not clipping on my mixer or software)

Clipping can occur at any point in the chain of electronics and may NOT show on your mixer.

Also cheeck your phantom power voltage sent to the mic. Some mixers send much lower than the +48 volts and clipping within the mic electronics can happen with these. Check the voltage between either pin 2 or 3 and pin 1 of the XLR. Note that the pin numbering on XLR's is funny... search google for diagram.

Jul 19, 2010 | SE Electronics Professional Microphone

1 Answer

Telex 56 to cobra 4 pin

Hi there!!

the yellw wire is not used on the microphone conector most of them are just cut and left in there loose as long as its not shorting out on anything!! The wiring for the telex 56 for your radio Cobra 29 LTD is as follows: PIN #1 Shield & Red, PIN #2 White, PIN #3 Blue, PIN #4 Black, Yellow wire not connected!!

If you notice when you have the connector apart on the back of the pins where the wires get soldered to the pins are numbered so you will know which pins they are or on the front side of the connector the pins are also marked wich numbers they are!! If you have any other questions please feel free to e-mail us at:

Apr 18, 2009 | Telex M-560 Consumer Microphone

3 Answers

Don't know the conections of blue or red

If we're talking about the microphone cable wiring on a low impedance mic remember this. Cheap mic cables with XLR's on both ends often have no standard color code to follow. True pin 1 is ALWAYS ground (shield wire) but the other two wires could be any color of the rainbow. Look for small numbers beside each pin of the XLR connector and make sure that pin two on one end of your cable, is also pin two on the other end as well....etc. Special note: The XLR connectors set screws have reversed threads and it's the same for the XLR male plug in the bottom of the microphone as well.....Glen

Dec 24, 2008 | Shure Beta 58A Professional Microphone

1 Answer

Mic problem

Hi and welcome to FixYa,

Offhand, the 4 pin mic connector and corresponding pin # would depend on the communications equipment the Astatic was initially wired for. However, the color coding of the wires in an Astatic would be:
  • white - mic audio;
  • shield/blue - gnd;
  • black - NC or speaker;
  • red - NO or PTT;
  • yellow - not normally used.
Good luck and Thank you for using FixYa. Happy Holidays.

Dec 09, 2008 | Astatic 636L Noise Canceling Microphone...

1 Answer


i want to know the secret atm pin number

Jun 16, 2008 | Audio Technica Artist Series ATM410...

Not finding what you are looking for?
Audio Technica Artist Series  ATM410 Professional Microphone Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Technica Audio Players & Recorders Experts


Level 3 Expert

4678 Answers

Clif Roberts

Level 2 Expert

87 Answers

sean tan

Level 1 Expert

15 Answers

Are you an Audio Technica Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides