Question about Bushnell PinSeeker 1500 20-5103 Rangefinder

1 Answer

Pinseeker is blurred

Objects started appearing blured after about a year of use. I compared it against another Rangefinder and the yardage is the same or close to the same. It reads ok, just has a blur, like the lens is out of focus or went defective. Any suggestions on taking it apart or what to do would be appreciated.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There is an adjustment ring bewteen the eye piece and the body. Make sure the white ines are lined up and it should come back into focus.

Posted on Jul 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rangefinder is 4+ seasons old - will not lock-in


for this you will need to send the unit into their repair at 8500 marshall drive lenexa ks 66214 4-6 week turnaround and put your name address and telephone number inside the package. if there is a cost they will send an estimate.

Mar 11, 2010 | Bushnell Pinseeker 1500 Rangefinder

1 Answer

Doesn't always show yardage


for this you will need to send the unit into their repair at 8500 marshall drive lenexa ks 66214 4-6 week turnaround and put your name address and telephone number inside the package. if there is a cost they will send an estimate.

Oct 27, 2009 | Bushnell Tour V2 Pinseeker Laser...

1 Answer

I have a bushnell 1500 which has stoppeed reading yardages


for this you will need to send the unit into their repair at 8500 marshall drive lenexa ks 66214 4-6 week turnaround and put your name address and telephone number inside the package. if there is a cost they will send an estimate.

Sep 11, 2009 | Bushnell PinSeeker 1500 20-5103...

1 Answer

Dropped from a golf cart....numbers dont come on


If you hear a rattle.....The "shock" may have broken a internal lens. (BAD) IF not, you may have just knocked it out of alignment. The rattle is the snake...and it bit you. NO rattle....It may can be re-aligned.

Good Luck!!!!!

MTG

Jun 18, 2009 | Bushnell Pinseeker 1500 Rangefinder

1 Answer

Bushnell 1500 pinseeker with slope+/- to go from M to Yards


Hold down the "MODE" button until the "M" starts to flash......touch the mode button again till the "Y" flashes........then touch the "FIRE" button on top.....(square button) Then it will be set to read in yards....not meters.

mtg

May 16, 2009 | Bushnell Pinseeker 1500 Rangefinder

1 Answer

Tour v 2 , it doesnt show the actual yardage and I didn't try i


Make sure the battery is good. (Go to a radioshack and have them measure the voltage). It should be 3.1 to 3.2 volts. The reflectivity of objects being measured is a factor. Lighter colors reflect better than darker colors. Larger objects reflect better than small ones. License plates, highway signs are very reflective. You should be able to hit one of those from more than 700 yards away. Make sure the Pinseeker mode is on and try.....(touch the mode button and the flag comes up on the screen) Don't hold the mode button down for more than 5 sec or you will switch the unit to meters instead of yards.

Mar 24, 2009 | Bushnell Yardage Pro Tour Rangefinder

1 Answer

No yardage displayed


The rangefinder is out of alignment. Vibration, dropping these units make small mirrors inside move slightly. Over time the receiver cannot see what the transmitter puts out. Bushnell can fix, 4-5 weeks w/o unit.

Mar 18, 2009 | Bushnell PinSeeker 1500 20-5103...

1 Answer

Yardage does not shows up at times


First, make sure you are using alkaline batteries only. Heavy duty batteries don't generate enough current for the laser to operate properly. (pg4-para2 of the manual) If the rangefinder hits targets 120 yards or less and doesn't hit targets farther....the unit needs an alignment. Send it in to bushnell, they will repair it.

Feb 16, 2009 | Bushnell Pinseeker 1500 Rangefinder

1 Answer

My Pinseeker will turn on but will not give any yardage.


Sounds like the unit needs an alignment. If the crosshairs appear in the display and stay on....it needs a CPU board and reprogramming.

Jan 13, 2009 | Bushnell Medalist Rangefinder

2 Answers

LOB ...what does it mean ????


LoB =Low Battery condition

This will happen will new heavy duty batteries also. They don't generate enough current to operate the laser properly. Use alkaline batteries only. (pg.4-para 2 of the manual)

Nov 27, 2008 | Bushnell PinSeeker 1500 20-5103...

Not finding what you are looking for?
Rangefinders Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bushnell Rangefinders Experts

kakima

Level 3 Expert

96396 Answers

isaac johny
isaac johny

Level 3 Expert

796 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Bushnell Rangefinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...