Question about Microsoft Xbox 360 Elite Console

1 Answer

The remote are not connected to the system - Microsoft Xbox 360 Elite Console

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 43 Answers

Press the little black button on the top of your controller and press the little black button on your console next to the memorie care/ plug and play spot. This should make the power button and the controller spin and they should sync together. =]

Posted on Nov 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not start in the morning with (remote start)


sounds like poor connection when cold no start when car heats up good connection go back to installer of remote start/they have wiring diagrams when they installed it

Dec 21, 2013 | 5103L Security/Remote Start System

Tip

How to Enable Windows 7 to make a Remote Desktop Connection


1. Go to Control Panel>System>Advanced System Settings

2. Go to Remote tab.

3. Under Remote Assistance, put a check mark on Allow Remote Assistance connections to this computer.
Note: This automatically adds Remote Desktop exception to Windows Firewall.

4. Click on Apply.
1. Go to Start>All Programs>Accessories>Remote Desktop Connection

2. Enter the Computer Name or IP address of the computer you wish to connect to.

3. Click on Connect.

4. For more connection options, click on Options

Here you can save the connection profile, adjust display properties, run specified programs upon connection, adjust connection bandwidth, etc.
For more information on specific tabs, click on Help.

on Mar 23, 2010 | Computers & Internet

1 Answer

Connected all wires as instructed and when battery is hooked back up, siren just blast and remote wont stop it.


There are two reasons that the unit does not respond to the remotes: the antenna is not connected or, the remotes are not programmed to the system. Check to see if the antenna is hooked up. Next, make sure the remotes are programmed to the system. The next time you connect the battery, manually disarm the alarm by turning on the ignition then, press and release the programming button on the antenna.You should here one chirp(disarmed). Try to operate the unit with the remotes after the unit is disarmed.

Mar 19, 2011 | CA6550 Codealarm Remote Start Security...

1 Answer

AUDIOVOX CAR APS787N ADVANCED REMOTE START DOES NOT FUNCTION EVEN AFTER EVERYTHING IS CONNECTED PROPERLY.


If everthing is properly connected and the system does function,you may need to program the remotes. But first,let's check a couple of things. Turn the ignition on and press and release the push button LED three times and check for a response.The alarm should chirp one time. If the alarm chirps one time, press and release the lock button on the remote. If the alarm responds with a long chirp, press and release the push button LED one time,should hear two chirps; press and release the unlock button on the remote. The alarm should respond with a long chirp. Press and release the push button LED one time, you should hear three chirps, press and release the green button. You should hear a long chirp from the alarm. Press and release the push button LED one time, you should hear four chirps from the alarm; press and release the (1)button on the remote. continue the process for button(2).Now, if you do not hear the one chirp in the beginning, the system is not responding. Check your power and ground connections. If the system does chirp but, no response from the remote, check your antenna cable for proper connection at the module and the antenna. If the connections are fine, check the remote. Also,it is possible that there is major RF interference where you are located. If all of the above check out, try moving the vehicle to a different location and test.

Oct 13, 2010 | APS787N Advanced Remote StartKeyless Entry...

1 Answer

Rs2100 bookshelf stereo


The Audio System does not respond to the remote control.
1. To reset their connection, turn on the remote control and switch the Audio System to Standby mode.
2. In Standby mode, press and hold both INFO and SOURCE on the front panel of the Audio System. It is reset to default when"RF ID clear" displays.
3. Press and hold both PROGRAM and SELECT on the remote control. When “ID claer” displays on the LCD of the remote control, the connection is reset.
4. By now the remote control and the Audio System should be connected to each other. Press and hold PROGRAM and SELECT on the remote control again. When
“ID Locked” displays on the LCD of the remote control, the connection between the remote control and the Audio System is locked.

Jun 06, 2009 | RCA RS2100 Shelf System

3 Answers

MY REMOTE ALWAYS SHOWS ME REM506....


The Audio System does not respond to the remote control.

1. To reset their connection, turn on the remote control and switch the Audio System to Standby mode.
2. In Standby mode, press and hold both INFO and SOURCE on the front panel of the Audio System. It is reset to default when"RF ID clear" displays.
3. Press and hold both PROGRAM and SELECT on the remote control. When “ID claer” displays on the LCD of the remote control, the connection is reset.
4. By now the remote control and the Audio System should be connected to each other. Press and hold PROGRAM and SELECT on the remote control again. When
“ID Locked” displays on the LCD of the remote control, the connection between the remote control and the Audio System is locked.

May 07, 2009 | RCA RS2100 Shelf System

1 Answer

Remote desktop connection


It sounds like you had a pre-release version of RDC 6.1 installed which you should have uninstalled before installing SP3.

Check this out - under "Remote Desktop Connection" you might find the solution you're looking for.
http://download.microsoft.com/download/c/d/8/cd8cc719-7d5a-40d3-a802-e4057aa8c631/relnotes.htm

Hope this helps! : )

Jun 03, 2008 | Microsoft Windows XP Professional With...

1 Answer

Static ip


goto start menu -> accesories -> remote desktop connection


after that a window will open asking for ip.... if u give the ip it'll connect to that system and ask for username and password of the system to be remote accessed....

Mar 01, 2008 | Computers & Internet

Not finding what you are looking for?
Microsoft Xbox 360 Elite Console Logo

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Video Game Consoles & Games Experts

marley mcelhinney

Level 3 Expert

490 Answers

Tre Elkins

Level 3 Expert

643 Answers

Martin Murray

Level 3 Expert

1623 Answers

Are you a Microsoft Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...