Question about Dewalt 18 Volt Compact Drill Kit

1 Answer

The head is loose and moves back and forth - Dewalt 18 Volt Compact Drill Kit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dewalt Master
  • 7,733 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Moen faucet has little hot water pressure...cold is good.. Removed stem and water pressure good coming out of faucet body


inside the cartridge is a pressure balance cylinder. If it does not side back and forth with a clicking sound when shaken the cylinder needs to be unjammed. carefully push the brass handle head backwards exposing the inside center out of the back of the of the cartridge. use an ice pick into the side of the inner cartridge to wedge the inner balancer to move. once loose, reassemble. If you cannot get the balancer loose, replace the cartridge.

Jan 28, 2017 | Moen Plumbing

1 Answer

Dura Ace di2 front derailleur 10 speed (7970) not shifting correctly. Moving back and forth with clicking sound. How do we fix?


First, is cable tight, it may be that the cable has loosened or stretched. In this case, Put chain on inside spocket, loosen hex head bolt, pull tight, retighten hex head.
It also could be the limit screws have vibrated loose. There are two of them on the top of the derailleur. Make small adjustments in one screw, check to see if it improves shifting or makes it worse. You didn't say whether it was the small or larger spocket. The limit screws control how far in or out the derailleur moves. Read more on Shelton brown .com under derailleur heading

Sep 16, 2014 | Shimano Dura-Ace Di2 7970 Front Derailleur...

1 Answer

Broken Lexmark X9350 printer


That is the print head band and gear.. You said it was new? I would be calling Lexmark for warranty support as that should not be that way. So to answer you question it goes inside and connects to two pullies to move the head back and forth.

May 30, 2013 | Office Equipment & Supplies

1 Answer

When driving frequently the vehicle will start swinging back and forth like you are moving the steering wheel back and forth you let off the gas and it quits for awhile been aligned and checked why?


was the suspenssion checked out before the alignment was done?? something is loose/worn out. i would be looking at the lower control arms/bushings on lower control arms.something tells me that who ever did the alignment didnt check out the suspenssion the right way or at all. you can not do alignment if stuff is loose.

Sep 17, 2012 | 1988 Nissan Pathfinder

1 Answer

Left front clunk noise over the bump


most likely bad strut /shock ----grab tire at 3 and 9 and move back and forth if sloppy , noise or loose check idler arm and tie rods ---grab top of tire and move back and forth if loose check control arms and ball joints push down on fender if bouncy or makes noise check strut/shock for problem

May 13, 2012 | Cars & Trucks

1 Answer

Hp 430 plotter


does the belt look ok? sounds like you have some rubber stuck in the motor gear.

Oct 22, 2009 | Office Equipment & Supplies

2 Answers

I get a 6a00 error, the first time i start up my canon pixma mx850. I tried to move the printerhead manually and that works fine. But i still get this error everytime. When I look at the sliding mechanism...


if it's 6A00 then theres a problem with the cleaning unit where the printhead parks. Look for any paper scraps in that area,
the two foam pads that must cover/protect the heads when the cartridge is parked are jammed up, preventing the head cleaning squeegee from moving back and forth. Just to the right of these pads is a piece of blue plastic, part of the assembly holding the foam pads . very gentle downward pressure on this blue plastic frees the pads and the squeegee could move back and forth again. and will clear ur issue

there is a safety pin lodged under the far right side (home base). gently push the unit to the left to expose the imposter, and remove it

regards

Aug 16, 2009 | Canon PIXMA MX850 Multifunction Printer

1 Answer

Printer does not print but on screen message is "printer cradle cannot move". Print would move back & forth @ one end, moves to the other end to repeat the back & forth movement and then stop with...


This generally occurs when the tracking ribbon becomes dirty and the print head travel cannot be tracked. Open the cover as you would to change your ink cartridge and locate the clear plastic strip behind the print head. Very gently wipe the ink residue from the strip using a cloth damp with water. You should be able to move the print head manually enough to clean the entire strip. Again be very careful as the strip hooks on the left side and is very difficult to reattach.

Aug 11, 2009 | HP DeskJet F380 All-In-One Printer

1 Answer

PC-940 Cartridge stuck


Turn off machine, you can move the cartridge head back and forth when it is off. If it won't move there is something that is loose and is in the way, check.
Not sure if you mean it is stuck when it was moving or if the cartridge is stuck in the printer?

Nov 25, 2007 | Canon PC-940 Black and White Copier

Not finding what you are looking for?
Dewalt 18 Volt Compact Drill Kit Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...