Question about Zebra LP 2844 Thermal Printer

3 Answers

Wont print this printer has always worked and it functions all but the labels come out blank.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Check to make sure you have direct thermal labels. You can test this by scratching your fingernail across the label quickly. You should see a black line. This printer uses the same paper as a ups or fedex label. test a ups of fedex label with the fingernail test. Does it look the same? or call Andrew @ 908-725-1699

Posted on May 08, 2009

J'ai le meme probléme, sous wind xp et j'utilise le programe fourni dans le cd de zebra

Posted on Jul 03, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 148 Answers

What program are you using to print with and what operating system?

Posted on Jun 28, 2008

2 Suggested Answers

  • 31 Answers

SOURCE: I have a zebra TLP 3844-Z printer. My printer

Sounds like it is set to do a label length check at power on. Go into your printer preferences and set it to "do nothing" on power up.

e07a00e.jpg

Posted on Jun 27, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Easycoder C4 Printer wont print


See if this can help:
epsfiles.intermec.com/eps.../1-960572-01%20UG%20EC%20C4.pdf

May 26, 2014 | Intermec Easycoder C4 Therm Label Printer...

1 Answer

Prints label then prints a blank


This is always a calibration or label template size issue.

Feb 04, 2013 | Zebra Eltron LP 2824 Thermal Printer

1 Answer

Kodak printer will not print on avery label paper. Have been on teck support with anurag s for about an hour and tried again to print labels.


Hi , i have been using avery templates and label paper at work for ages and always printed off without problems on my lexmark . I bought a Kodak however and all of a sudden I could no longer print off my labels , when I put paper in it just came out blank and said paper wrong size .I could not find any solutions at all and was tearing my hair out . I just kept trying different things and all of a sudden I changed a setting and it worked perfectly.When you go to print your label change the ' scale to paper size ' function to A4 and then it will print.
hope this helps

Feb 28, 2011 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

Printing in page mode feeds extra blanc labels


Make sure,
you firmware is right one for that printer because in most of cases it happens due to wrong firmware and bad ADF kits. so check your ADF kids and if you find them fine the install updated firmware on in.
And put job seperator option always as disabled2168eac.gif
once you done with these all then turn your printer off and turn it back on.

post back if any thing changes and rate all answers.

Good luck



Feb 24, 2009 | Epson TM-L90

1 Answer

Zebra LP2443 thermal label printer wont print


Hi Buck,

What type of labels are you using?

Cheers

Bob

Jan 12, 2009 | Zebra LP 2443 Thermal Label Printer

2 Answers

I get 2 labels(1 with data and 1 blank)for every label printed


THE LABEL SENSOR IS NOT SENSING THE BEGINNING OF THE NEXT LABEL

Clean the photo eye that senses the label gap with a q tip and alchol

Open side door release print head and remove label stock you will see small photo eye clean

put printer in manual mode( switch 1 on to and 1 on botom on

turn printer on it should advance one label and hit skip it should advance another

put back in computer mode

should work now if it still skips check yur label desigh=n software and label mode (continuous or sense label)


Best of luck to you



Dec 29, 2008 | Intermec EasyCoder 3400 Thermal Label...

1 Answer

Printing blank labels


I am having the same problem! Printing blank labels. Don't know what's wrong now. It was working fine yesterday.

Jul 22, 2008 | Dymo LabelWriter 400 Thermal Printer

1 Answer

Zebra 2824


if you see that it is like printing a card. check your thermal print head maybe its not working.

Jun 23, 2008 | Zebra Eltron LP 2824 Thermal Printer

1 Answer

Printing addresses on labels


did set the parameters in the system before printing labels you can make a new printer control in printers section to only be label printed with the same printer you use
when you goto print click on the new print control that you have set for labels this way your software wont get the big confusion of paper or labels

May 07, 2008 | HP OfficeJet 6210 All-In-One InkJet...

Not finding what you are looking for?
Zebra LP 2844 Thermal Printer Logo

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...