Question about Toshiba 50HX81 50" Rear Projection Television

1 Answer

No sound or picture

TV clicks-on but does not provide sound or picture television clicks on,power indicator light on but it sounds like a switch goes off,no picture no sound.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toshiba Master
  • 8,617 Answers

Your relay is turning off most likelt due to on of the stanby voltages being out of parameters I would check the low voltage regulators and the horizontal output transistors.

Posted on Jun 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

STANDBY INDICATOR LIGHT BLINKS 15 TIMES WHEN TV IS TURN ON NO PICTURE OR SOUND


Hi,do you hear any strange noises? If you hear clicking or like wanting to turn on it could be the board that powers the lamp it's called the ballast.It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator.But if you don't hear any strange noises,tv is around 6000 hrs,2-4 yrs,It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator, it could be time to replace the lamp.

Dec 05, 2010 | Sony KDS-60A2000 60" HDTV

1 Answer

I have a Toshiba 51h84.I push the power button and I get a solid red power light. There is a click from inside, kind of like a relay clicking on. No picture, no sound. If I leave it on I get an occasional...


Tv have "LAMP" indication LED light blinking?The tv projection lamp is dead,require changing.Hearing alot of clickings sound too?Mean the board,call the Ballast board is dead.Require change the Ballast too.The Ballast board,the board that help to ignite the projection lamp.

Aug 06, 2010 | Toshiba 51H84 51" Rear Projection...

1 Answer

No picture or sound


Hi,do you hear any strange noises? If you hear clicking or like wanting to turn on it could be the board that powers the lamp it's called the ballast.Here's the instructions to replace it :http://www.fixyourdlp.com/guides/samsung/bp47-00033a.php It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator. But if you don't hear any strange noises,tv is around 6000 hrs,2-4 yrs,It's major symptoms are clicking,electrical sounds,shuts off and on and get the lamp indicator, it could be time to replace the lamp.The lamp you need is XL2100 you can find it here:http://www.discount-merchant.com/Sony-XL-2100U-TV-Lamp-p/sony_xl-2100u_replacement_lamp.htm?Click=48173 .Have a blessed one!

May 03, 2010 | Sony Grand WEGA KDF-50WE655 50" Rear...

1 Answer

No sound no picture


Dose the lamp light indicator in front panel flashes?Than lamp must change.

Mar 16, 2010 | Panasonic PT-52LCX65 44" HDTV

1 Answer

Standby/timer light stays on red. no picture or sound on tv.


my sony red light flash.but it will not turn on just clicks

Nov 26, 2008 | Sony KP-48S75 48" Rear Projection...

1 Answer

Clicking sound!


The TV is on protect mode. The clicking sound is the protection switch that keep turning the TV off to prevent further damage, this happens when a fault had been detected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

Apr 11, 2008 | RCA P60921 60" Rear Projection Television

Not finding what you are looking for?
Toshiba 50HX81 50" Rear Projection Television Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

The Knight
The Knight

Level 3 Expert

68427 Answers

Are you a Toshiba Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...