Question about Epson GT-2500 Flatbed Scanner

Open Question

Error red light is flashing scanner does nor work epson gt-2500 help

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mohanchennai
  • 490 Answers

SOURCE: Epson 2400 scanner red light flashing

Normally any new scanner fresh from the factory has a 'lock' which prevents damages due to transportation. Ensure it is unlocked.
S. Mohan

Posted on Feb 06, 2009

Ad
  • 146 Answers

SOURCE: Epson perfection 2400 photo scanner stuck with flashing red light

You may have accidently pushed the LOCK button - this button is used to LOCK the carriage into place when moving the scanner to another location or shipping it.

Check for a button and the picture of a LOCK, it is usually at the back of the scanner, you can push it left or right, and you have an open lock and a closed lock picture under it. Make sure you didn't accidently push it to the LOCK position when holding the scanner - that loud sound means your carriage is locked and cannot move - once you set the button to UNLOCK this should solve your problem.

Posted on Aug 18, 2009

  • 1 Answer

SOURCE: my epson scanner 3170 is flashing a red light and

Disconnect the cable between the scanned lid and the bed. Lift off the lid. Using a small Phillips head screwdriver, remove the two screes that are located where the lid's hinges were. Carefully lift off the top portion of the bed starting at the back. As you approach the front, push it towards the control panel to remove. The front pulley will have either one or both of the plastic flanges will be broken (hopefully just one. In my case, I just used duct tape to hold the pulley down tightly. Power it up to ensure that it's fixed before puttingthe top part of the base back on. If it's not connected to your computer, you should get a flashing green light, or solid green if it's talking to your computer. Put the top part of the bed back on, screw it down and re-attatch the lid.

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Epson Perfection 1660 scanner is stuck. The


you want to go into the error count menu on the printer and reset after you have corected whatever caused the malfunction

May 30, 2010 | Epson Stylus Multifunction Inkjet Printer/...

1 Answer

My epson 3490 photo scanner isn't working theres a red light on the front of the scanner which is flashing


If the start button light is flashing red, it is because of one of the following problems:

  • The scanner is not connected to your computer properly or your software is not fully installed.
  • The transportation lock is locked. Slide the lock to the unlock position.
After trying these solutions, unplug the scanner to turn it off, then plug it back in.

Sep 30, 2009 | Epson Perfection 3490 PHOTO Flatbed...

1 Answer

Epson 2400 scanner red light flashing


Normally any new scanner fresh from the factory has a 'lock' which prevents damages due to transportation. Ensure it is unlocked.
S. Mohan

Feb 05, 2009 | Epson Perfection 2400 Photo Flatbed...

1 Answer

Flashing red light & noise


I've just discovered that this means the "transportation lock" is on: at the back of the scanner, put the plastic switch into the 'unlock' position. See this Epson support page for more details.

Dec 23, 2008 | Epson Perfection 1660 Photo Flatbed...

3 Answers

Epson 3490 scanner red light flashing message that printer cannot properly communicate with pc


If the start button light is flashing red, it is because of one of the following problems:
  • The scanner is not connected to your computer properly or your software is not fully installed.
  • The transportation lock is locked. Slide the lock to the unlock position.

Jul 16, 2008 | Epson Office Equipment & Supplies

5 Answers

Epson GT5500 Flatbed scanner


unfortunately Epson has not made a driver for this scanner that is compatible with Vista and from the looks of it, they don't seem to have any plans on making one!
Sorry

Jan 29, 2008 | Epson GT 5500 Flatbed Scanner

1 Answer

Epson GT30000 Document feeder error


if the ready light is off, and the error light is flashing, it indicates an interface error. please check all your cables.

Sep 16, 2007 | Epson GT 3000

1 Answer

Scanner not responding to preview scan


Try this as a last ditch effort. Remove the software. Reboot the computer and come off line. Disable the Anti Virus program. Now install the soft ware. Then try. If the red light still flashes then assume it is new scanner time.

Jul 26, 2007 | Epson Expression 1640XL Flatbed Scanner

Not finding what you are looking for?
Epson GT-2500 Flatbed Scanner Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...