Question about Brother HL-2030 Laser Printer

1 Answer

Brother HL-2030 sensors

Hi,

Thanks for pointing me into the direction of the sensors. I looked into the printer but couldn't identify the sensor you tried to point out. I tried to move around with the "sensor" indicated below.
Also I checked to see if all screws were fixed properly. Like for eg. the screw in the picture.

Up till now nothing helped, I suppose I'm looking in the wrong place.

Thanks,
Kris

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 638 Answers

Let me search some more data which can be helpful to u.

Posted on Jun 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service code interrupt


Error type T11 [Pressure-control motor lock]
T11-***
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service
Reset method Jam reset or switch on power again
Error point Error conditions
600
Timeout error for reducing pressure (OFF -> ON) during print-pressure home
positioning.
601
Timeout error for increasing pressure (ON -> OFF) during print-pressure home
positioning.
602 The print-pressure limit sensor does not change during print-pressure operation.
620 Print-pressure operation was called with the print-pressure motor locked.
621
Incorrect print-pressure operation timing (print-pressure operation command was
received when the print-pressure should not change).
622 Sensor A is ON and sensor B is OFF during movement from area A to area D.
623 Either sensor A or sensor B is ON during movement from area D to area A.
624 The current area data is undefined.
625 The target area data is undefined.
626 Timeout during relative print-pressure movement.
Error type T12 [Master-disposal-section motor lock]
T12-***
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service
Reset method Jam reset or switch on power again
Error point Error conditions
305
The master compression sensor does not go ON within 6.5 s after the master
compression motor operates in the return direction.
306
Master compression sensor does not go OFF within 2 s after the master
compression motor operates in the compress direction.
307
The master compression sensor does not go ON within 6.5 s after the master
compression motor operates in the compress direction, and the mastercompression-
motor limit sensor cannot count up until the compression-limit
position.
309
The master-compression-motor limit sensor does not change within 200 ms
during compression operation.

hope to be of help

Sep 27, 2013 | Riso RP 3700

1 Answer

Rizo ez200E p12-309


Error type P12: System ErrorError point 309: Master-compression-motor encoder sensor count did not change as the master compression motor activated in the compress direction and moved out from the home position.
Try this: Press reset-key. If recovery fails you machine needs service.

Sep 19, 2012 | Riso RZ220 Duplicator

1 Answer

Riso 390U error code p19 208 .... doesnt seem to be loading the master roll correctly, any suggestions?


Error P19-208
Error type P19: Thermal-pressure motor lock Error point 208: TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the decompressing direction.
Hints: Check mentioned sensor. Check mentioned motor.

Jan 06, 2011 | Riso RZ220 Duplicator

1 Answer

Canon PIXMA MP510 Printer says "no paper" please help!


Hi,

It is best that you take your printer to a certified service center for Canon, its possible that it just need cleaning and that something is tripping the sensor and sending the wrong signal. Gheck if the paper feeding sensor is ok, usually the trigger could be broken, compare it with the same printer and look for differences.

On the otherhand, if you are sure and you are a technical person with repair experience, please check with the Canon main distributor or sales office near you. They have parts specific to your needs, if not they can point you to the right place.

Another alternative is to go a Canon repair shop and ask if they have a scrap printer with the same model as yours.

Jul 29, 2010 | Canon PIXMA MP510 All-In-One InkJet...

1 Answer

Ribbon Error


According to the user's manual this message indicates a problem with the ribbon sensor. As a test, set the unit for thermal direct printing and attempt to print a barcode. You will not see the code if yoiu are expecting thermal transfer, but the paper/label should feed like it is printing. That will indicate that the printer is functioning. At this point, the sensor needs to be replaced.

Hope this helps,
Dan

Apr 22, 2010 | Toshiba TEC B-472 Thermal Label Printer

2 Answers

Paper jam problem


Hi,
Cause : Paper jam.

Remove the jammed paper. Unplug the printer from the mains and PC. Inspect the rollers, etc for tiny paper piece(s) that may be stuck, or other debris. Try to clean rollers and make sure they are dry.
Keep printer unplugged for about 2 minutes and replug and try a test print.
Also make sure that you have waited long enough for the printer to heat up before giving a print job.
Finally, it could be an issue with the paper sensor. If this is the case, you will probably have to take the printer in for servicing..

Hope that helps! Please rate my response.

Thanks
Have a good day.

Nov 26, 2009 | Samsung ML-2551N Laser Printer

1 Answer

Zebra Z4Mplus won't calibrate 2" Circle Labels


try to set the printer to the factory default setting

Aug 13, 2009 | Zebra Z4M Printer

2 Answers

HDP600 print ribbon will not align properly. Using the diagnostics section, the color ribbon, ymckk, will not align to its correct starting point so that an accurate id card can be produced. The data is...


If card image is spread out into the yellow panel and the next magenta panel ...and so on skiping panel of the ribbon, then is defenitlly a sensor mis calibration problem. Check if you working in a place where to much natural light is present. The printer needs to detect the diffrent colors of the ribbon panels to print without skkiping them. re-calibrate the sensor. also as to "see or sense" the timing white marks on the ribbon that separates each panel.

I hope i help
ventas@intesys.org

Feb 25, 2009 | Fargo HDP600 Thermal Printer

2 Answers

Error code U9


hi im jules_09,are you sure its an error code?chek first all sensor on front door and other parts of the copier that has a sensor,

Nov 02, 2007 | Printers & Copiers

Not finding what you are looking for?
Brother HL-2030 Laser Printer Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Printers & Copiers Experts

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

John mullen

Level 2 Expert

245 Answers

Are you a Brother Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...