Question about Honeywell Programmable Thermostat Heater

1 Answer

Have a honeywell focusPRO th6000 series thermostat. it was working fine then all of a sudden, when I went to override the temp, i noticed the display was flashing "set time"... also displayed is "done" in lower left corner and "Set day" in bottom center. The time is also displayed but is changing on its own. I can not get it to reset at all and have no heat!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have Hineywell FocusPro TH5000 and auxiliary heat is on today, is that normal?

Posted on Jan 29, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: permanent hold message on thermostat

press run program.... from there, set the schedule for maximum efficiency. permanent hold only shows up after the hold button has been pressed 2-3 times. If this does not fix the issue, there is a master reset button on the thermostat that will set all settings back to factory default.

Posted on May 17, 2009

  • 96 Answers

SOURCE: Thermostat auto-changeover mode unavailable

when you programed it did you go through all the setup #1-0 ,#3-0 ,#5-5 ,#12-1

Posted on Nov 25, 2008

Blue Dog
  • 75 Answers

SOURCE: Need guide to use th6000 honeywell thermostat

Right here. (http://customer.honeywell.com/techlit/pdf/69-0000s/69-2026.pdf)
Good luck!

Posted on Jan 01, 2009

  • 70 Answers

SOURCE: Thermostat not shutting off heat.

has the thermostat been programed to tell it what type of system you are using. If you look in the papper work you should find where it ells you to hold down the button lower left and top right button i think those are the two i don't have the papper work with me right now but i can get if you need more information on how to set it

Posted on Jan 22, 2009

  • 21 Answers

SOURCE: Honeywell TH6000 series thermostat does not turn Fan on.

It's one of two issues; either the wiring to the thermostat is incorrect, or possibly you have an open ground. Depending on your system the wires at the thermostat end might have to pair up on one lead. go to where your unit is and look at the schematic for the control board, it will let you know what color you are looking for on the blower lead -- then make sure the corresponding color matches at the thermostat. Knowing the make and model of you unit and the board on it would allow me to be more specific, hope this helps you out some in the meantime.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set the temporary or permanent override feature on the Honeywell RTH2310B model thermostat?


To set the temporary override, press arrows up or down to desired temp. This will keep temperature
at temporary setting for 2 hours then return to programming. To permanent override press MODE button until schedule period number disappears (number inside little house on stat). Then adjust temp with arrows. Press the MODE button again to cancel override and return to programmable.

Jan 25, 2011 | Honeywell Programmable Thermostat Heater

1 Answer

I have a honeywell t stat th6000 for htg only having problem get my gas valve to go onfurnace is working but no heat


As long as this is a 24 volt thermostat, remove the thermostat from the sub base and connect the wires that are connected to terminals R & W. If the furnace works the problem is in the thermostat. Have you tried new batteries

Oct 29, 2009 | Honeywell Electronic Programmable...

1 Answer

Honeywell TH6000 series thermostat does not turn Fan on.


It's one of two issues; either the wiring to the thermostat is incorrect, or possibly you have an open ground. Depending on your system the wires at the thermostat end might have to pair up on one lead. go to where your unit is and look at the schematic for the control board, it will let you know what color you are looking for on the blower lead -- then make sure the corresponding color matches at the thermostat. Knowing the make and model of you unit and the board on it would allow me to be more specific, hope this helps you out some in the meantime.

Jun 17, 2009 | Honeywell Focus 6300B 5-2 Days...

2 Answers

Need a "trouble shooting" guide for FocusPRO TH6000


i have the heat set at 73 the temp in the house is getting colder it is at 67 now and it won't come on . why?

Jun 12, 2009 | Honeywell Electronic Programmable...

2 Answers

My thermostat quit working


Does it have batteries that need replacig. I think so. good luck.

May 31, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Thermostat not shutting off heat.


has the thermostat been programed to tell it what type of system you are using. If you look in the papper work you should find where it ells you to hold down the button lower left and top right button i think those are the two i don't have the papper work with me right now but i can get if you need more information on how to set it

Jan 21, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Need guide to use th6000 honeywell thermostat


Right here. (http://customer.honeywell.com/techlit/pdf/69-0000s/69-2026.pdf)
Good luck!

Jan 01, 2009 | Honeywell Electronic Programmable...

1 Answer

How to work my thermostat


Fan switch should be on auto in the heating mode and on in cooling. Contact the manufactuer on line for a new manual for this thermostat.

Ray

Dec 14, 2008 | Honeywell Electronic Programmable...

1 Answer

Thermostat auto-changeover mode unavailable


when you programed it did you go through all the setup #1-0 ,#3-0 ,#5-5 ,#12-1

Nov 24, 2008 | Honeywell Electronic Programmable...

Not finding what you are looking for?
Heating & Cooling Logo

1,016 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

587 Answers

Paul Carew

Level 3 Expert

2557 Answers

Cindy Wells

Level 3 Expert

5165 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...