Question about Amplifiers & Preamps

2 Answers

Old amp replacement

What can I substitute my ONKYO with?

Posted by on

  • Graeme Ross
    Graeme Ross May 11, 2010

    Hi filosopher

    Couple of questions before I can offer any advice to you. What model are you replacing, and why are you replacing it?

    regards
    robotek




×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,512 Answers

Best way to shop for a stereo is with your ears. Find what you like first, then worry about affording it after:) Best approach IO reckon:)

robotek

Posted on Jun 29, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 54 Answers

Helo again Well how about a newer onkyo stereo or a 5.1 channel surround sound.all are pretty solid units you should find them any where stereos are sold.
GOD LUCK BIGRED

Posted on Jun 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onkyo Amplifiers & Preamps


Hi ,try cleaning your volume control ,here is a video so you can DIY or contact your local service. :)

Dec 17, 2013 | Onkyo Amplifiers & Preamps

1 Answer

Onkyo M-282


check your amplifier output speaker impedance requirements..
example: 8 ohms...build a speaker 8 ohms in parallel or series connection..
check the impedance using ohmeter ..you must reach the required impedance..

use 1 cell battery to check if you speakers are in-phase...if one speaker did not ..reverse connection and check again ...to give the good sound...hope you understand my english..:)

May 24, 2010 | Onkyo M-282 2-Channel Amplifier

1 Answer

I have 1 center channel pre-out on back of my kenwood receiver. how do i hook it to the inputs on onkyo m-282 amp and then to center channel speaker?


Unfortunately can't connect it that way. The pre out is only meant to go directly into an amplifier that has all of the same inputs (front/rear, center and surround), not a standard receiver. (Pre amp to amp only, not pre amp to receiver) If your Onkyo doesn't have all the same inputs as your Kenwood preamp has outputs you will just use your standard left/right outputs from the Kenwood to your Onkyo input (CD, Tape, Phono,DVD etc) then use the outputs (front/rear, center and surround) from your Onkyo receiver and connect directly to your speakers..

Jan 01, 2010 | Onkyo M-282 2-Channel Amplifier

1 Answer

I have an ONKYO TX-SV717Pro amp. recently I lost


It could be that you lost the power supply to the surround amp IC or the Ic is defective. It should be mounted on a circuit board attached to the heatsink. Look for poor solder connections first. I don't recall the specifics of this model, but the surround amp IC should be easily located.

Update this with your progress and I'll try to locate the service manual in the meantime.

Dan

Oct 22, 2009 | Onkyo M-282 2-Channel Amplifier

1 Answer

Broken on/off switch on Onkyo TX-822/811 Tuner Amplifier


www.oaktreent. com

might have spare onkyo parts

Mar 22, 2009 | Amplifiers & Preamps

1 Answer

Amplifier moving spontaneously from one input to another cutting out used source


18years is good service you may want to look at upgrading to a newer model. If you have become close to this amp I think the processor for the amp is going bad and you would have to replace the entire board ,and on this old of set woud not be available.
GOD LUCK
BIG RED

Mar 27, 2008 | Amplifiers & Preamps

1 Answer

P-301 onkyo pre-amp


Hi juicer, If you use the switched outlet, then everything will be turned on/off when you operate the preamp power switch. Use the unswitched, then you have to turn off each unit separately. You choose which one you want. It wont matter.

What connection do you intend to use to connect the LBT zx6 to the Onkyo preamp??

Mar 20, 2008 | Amplifiers & Preamps

1 Answer

Onkyo A-RV401 amp is not sending any sound to the speakers.


The protection circuit is self resetting, it operates only when there is a fault condition in the amp. there is most probably a failure in the output stages of the amp causing a dc offset condition in the speaker output. The protection cct operates to prevent damage to your speakers. It may be difficult to offer a solution to you for this, it gets a bit complex to fix from here...you may have dry solder joint problems in the output stages, or more likely, failed output components. if you have a transistor checker(ohms meter), then you may be able to determine if any output transistors have failed, I recommend taking the amp to a good HiFi guy for repair. Many (including myself) often replace the all transistors to the last 2 stages when outputs fail. assures reliability in the future to repair this way, but the cost goes up a bit also. expect at least $120 to repair is it is a failed output stage.

Jan 03, 2008 | Amplifiers & Preamps

Not finding what you are looking for?
Amplifiers & Preamps Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amplifiers & Preamps Experts

 Grubhead
Grubhead

Level 3 Expert

4576 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68197 Answers

Are you an Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...