Question about Canon PIXMA iP4200 InkJet Photo Printer

1 Answer

Canon 4200 9 flashes, says camera attached and is none

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

Hello dear,
If you have a digital camera attach it to the printer and remove it once, switch the printer on/off if this resolves the problem thenits ok or carry the printer to the Canon Care as the pitchbridge connector or the logic card might be faulty.
Regards,
Manoj Joseph
+91 9352008418

Posted on Jun 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon ip100 portable printer ink cradle stuck on right hand side


I had this same problem. Count the number of blinks in sequence of the error light. it will flash green and yellow, and then just straight yellow for a number of flashes, then it will flash green again and the same number of yellow flashes again. Here is the diagnostic guide.

Two flashes: Printer is out of paper. Paper does not feed

Three flashes: Paper jam

Four Flashes: The Print Head Lock Lever is not locked properly / Ink tank is not installed properly. / Ink may have run out

Five flashes: Print Head is not installed./ Print Head is defective

Eight flashes: Ink absorber is almost full

Nine flashes:No response from connected digital camera or video camcorder/Connected digital camera or video camcorder is not compatible with this printer./PictBridge compliant devices are attached to both Direct Print Port and Bluetooth Unit Connector

Eleven flashes: Automatic Print Head Alignment failed

Twelve Flashes: Low battery level

Fifteen Flashes: Ink tank cannot be recognized

Seventeen Flashes: Ink has run out

Eighteen Flashes: Printer detected ink out condition

Nineteen Flashes: A USB hub is connected

Mine had 10 Flashes and the Print Carriage, was bad. Cost almost as much as another printer so thats what I did. I did take it apart and got it unstuck, but still didn't work.

Mar 10, 2014 | Canon iP100 Portable Printer

1 Answer

MY CANON BJC 4100 ISIT APLUG AND PLAY


If you are using XP here is a walkthrough:

1: Click START, then click on PRINTERS & FAXES

2: Click on ADD A PRINTER

3: At Welcome screen click NEXT

4: Select LOCAL PRINTER (if printer is attached directly to computer) and click NEXT

5: Choose LPT1 (in most situations) or a different port if not LPT1 then click NEXT

6: Select "Canon" in left window

7: Select "Canon Bubblejet 4100" or "Canon Bubblejet 4200" in right window

8: Click NEXT

9: Type name for printer or accept default name

10: Click No to "Do you want to print test page".

11: Click FINISH

Dec 20, 2009 | Canon Printers & Copiers

1 Answer

New laptop with windows 7. Pixma 4200 printer is


Did a cleaning as the last solution and just a general check of the printer's maintainence. Seems that something got mixed up when
the windows system was changed from xpp to w7. Now it is printing beautiful colors as before.

Nov 22, 2009 | Canon Printers & Copiers

3 Answers

No installer for Canon 4200


You can download the drivers off the Canon website. My fiance' has a Pixma 4200 and I was able to download the driver there a few months ago.

Jul 23, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Err 99 appears after every click for canon eos 30 D


Err 99, but lens-to-body problems are common- thought error 99 is a bit of a catch all- generally a lens and body conflict. And also Err 99 means that something wrong happened, but then it cleared out before it could be further determined.
Here is the blurb from canon to try:

Thank you for contacting Canon product support. I'm sorry to hear that
your EOS 10D is displaying an "ERR 99" message.

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

For factory service, forward your digital camera (remove the CF card
and battery) properly packaged and insured, with a letter describing the
difficulties. Be sure to include your name, address, telephone number,
and proof of warranty (if applicable). Send to the Canon Factory
Service Center at the following address:

Canon Factory Service Center
100 Jamesburg Road
Jamesburg, NJ 08831
Tel.# (732)521-7007

or

Canon Factory Service Center
15955 Alton Parkway
Irvine, CA 92618
Tel.# (949) 753-4200

Your equipment will be examined and you will be advised of the
findings.
The length of time for the repair will be dependent upon the nature of
the repair and availability of parts if needed. If the repair entails
something that is not covered in warranty you will be sent a written
estimate to the address that you have provided.

Please leave for me, a rating...

May 15, 2009 | Canon MF8180C Color Laser MFC Printer

1 Answer

I have a Canon Pixma iP 4200 printer and after I installed the ink 3 of them were flashing red and I cannot get the paper to feed. What can I do?


check for whether the cartridge is properly fixed to the bracket


---------------------------------------------------
Please don't forget to rate me "FIXYA"...thank you!

Mar 04, 2009 | Printers & Copiers

3 Answers

PIXMA iP8500


Error 5100 on Canon Pixma iP8500. flashes orange 2 times. Sounds like the paper isn't being picked up. But I don't know how to fix it.

Jan 03, 2008 | Canon PIXMA iP8500 InkJet Photo Printer

3 Answers

Inaccurate error message


mine does it with the cyan and it worked for awhile...if I take a cartridge from another ip42000 cyan, it works. Any ideas?

Dec 12, 2007 | Canon PIXMA iP4200 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA iP4200 InkJet Photo Printer Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96333 Answers

old marine
old marine

Level 3 Expert

1453 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...