Question about Kenmore 44102 Front Load Washer

1 Answer

Control panel lockout - Kenmore 44102 Front Load Washer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 1,902 Answers

Hello

This is a common issue with Kenmore front loads however, fixing it is quite simple. You can unlock the controls by pressing the DRAIN/SPIN button for 15 seconds. Please get back to me if you have any questions.
Kevin

Posted on Nov 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unlock control panel LFFH21F7HWG?


Press and hold the Control Lock key for three seconds
to activate or deactivate the function. The Control Lock
feature prevents the user from changing the temperature
and freeze settings. At the first press of any key, the
key press click tone will be heard and the display will
show "LO", but no other change will take place. Holding
the Control Lock key for three seconds will activate or
deactivate the Control Lock feature. After three seconds,
the accept tone sounds and the Control Lock LED (if so
equipped) is activated. In lockout mode, when any key
is pressed, the invalid key tone will be heard and "LO"
will be displayed for 1 second. When the lockout is
deactivated, the Control Lock LED is turned off and the
display shows "UL"

if this does not work unplug the freezer for 30seconds then plug it in. if all of the above fails replace the control.

Jul 04, 2014 | Frigidaire 20.3 Cu. Ft. Frost-Free Upright...

1 Answer

Controls for LG TV 37LC2D don't work


Take a good look at the owner manual for this set, either the control board is not plugged in or what is more likely is the set has a lockout feature for that board.

Some sets now have a panel control lockout and even a remote lockout or both.

its likely locked (the controls) out.

Dec 22, 2012 | Televison & Video

1 Answer

Key lock on


It would seem to have a front panel or control lockout feature, some sets have this and a remote lockout also.

The way to unlock will always be indicated in the owner manual-if have that read every page carefully.

If no manual try to Google the model number with "manual" to locate one

Dec 20, 2012 | Hyundai Q321 32 in. LCD Television

1 Answer

Samsung lcd tv can't find a source, buttons on remote control don't respond, nor buttons on the control panel on the right side of the TV device


consult the owner manual or call Samsung---this set likely has a lockout feature that locks both the remote and the keyboard out.

You might also want to research this by taking the model number and Google key words "remote lockout" etc.

Jun 01, 2012 | Samsung Televison & Video

1 Answer

My front passenger, rear driver and sunroof windows have all stopped working and up until 3 weeks ago worked fine.Rear driver and front passenger windows work fine. New battery put in today and no change.


Check the master window control panel on the drivers door. There is probably a lockout switch. It may have a window outline on one end and the same outline with an "X" over it on the other. Press the outline without the "X" and all your windows should work again.
As silly as that sounds, a lot of folks hit the lockout switch and don't know it. On the other hand, the lockout switch is bad.

Aug 03, 2011 | Mercedes-Benz S-Class Cars & Trucks

1 Answer

Oven lockout on oven wont do anything


What is the model number of the unit? Look on the inside of the oven door for it. When you say "lockout" do you mean the door lock is on or is there a light on the control panel displaying a lock?

Feb 04, 2011 | GE Ovens

1 Answer

What are the carrier 8000ts led error codes?


They are listed inside the front panel of the main unit.

LED CODE

EACH OF THE FOLLOWING STATUS CODES IS A TWO DIGIT NUMBER WITH THE FIRST

DIGIT DETERMINED BY THE NUMBER OF SHORT FLASHES AND THE SECOND DIGIT BY

THE NUMBER OF LONG FLASHES.

STATUS

11 NO PREVIOUS CODE - Stored status code is erased automatically after 72

hours. On RED LED boards stored status codes can also be erased when power

(115 VAC or 24 VAC) to control is interrupted.

12 BLOWER ON AFTER POWER UP (115 VAC or 24 VAC) -Blower runs for 90

seconds, if unit is powered up during a call for heat (R-W closed) or R-W opens

during blower on-delay.

13 LIMIT CIRCUIT LOCKOUT - Lockout occurs if the limit or flame rollout switch is

open longer than 3 minutes.

- Control will auto reset after three hours. - Refer to #33.

14 IGNITION LOCKOUT - Control will auto-reset after three hours. Refer to #34.

21 GAS HEATING LOCKOUT - Control will NOT auto reset.

Check for: - Mis-wired gas valve -Defective control (valve relay)

22 ABNORMAL FLAME-PROVING SIGNAL - Flame is proved while gas valve is

de-energized. Inducer will run until fault is cleared. Check for:

- Leaky gas valve - Stuck-open gas valve

23 PRESSURE SWITCH DID NOT OPEN Check for:

- Obstructed pressure tubing. - Pressure switch stuck closed.

24 SECONDARY VOLTAGE FUSE IS OPEN Check for:

- Short circuit in secondary voltage (24VAC) wiring.

31 PRESSURE SWITCH DID NOT CLOSE OR REOPENED - If open longer than

five minutes, inducer shuts off for 15 minutes before retry. Check for:

- Excessive wind - Proper vent sizing - Defective inducer motor

- Low inducer voltage (115VAC) - Defective pressure switch

- Inadequate combustion air supply - Restricted vent

- Disconnected or obstructed pressure tubing

- Low inlet gas pressure (if LGPS used)

If it opens during blower on-delay period, blower will come on for the selected

blower off-delay.

33 LIMIT CIRCUIT FAULT - Indicates a limit, or flame rollout is open. Blower will

run for 4 minutes or until open switch remakes whichever is longer. If open

longer than 3 minutes, code changes to lockout #13. If open less than 3 minutes

status code #33 continues to flash until blower shuts off. Flame rollout switch

requires manual reset. Check for: - Restricted vent

- Proper vent sizing - Loose blower wheel - Excessive wind

- Dirty filter or restricted duct system.

- Defective blower motor or capacitor. - Defective switch or connections.

- Inadequate combustion air supply (Flame Roll-out Switch open).

34 IGNITION PROVING FAILURE - Control will try three more times before lockout

#14 occurs. If flame signal lost during blower on-delay period, blower will come

on for the selected blower off-delay. Check for: - Control ground continuity

- Flame sensor must not be grounded

- Oxide buildup on flame sensor (clean with fine steel wool).

- Proper flame sense microamps (.5 microamps D.C. min., 4.0 - 6.0 nominal).

- Gas valve defective or gas valve turned off - Manual valve shut-off

- Defective Hot Surface Ignitor

- Low inlet gas pressure

- Inadequate flame carryover or rough ignition

- Green/Yellow wire MUST be connected to furnace sheet metal

45 CONTROL CIRCUITRY LOCKOUT Auto-reset after one hour lockout due to;

- Gas valve relay stuck open - Flame sense circuit failure

- Software check error

Reset power to clear lockout. Replace control if status code repeats.

If status code recall is needed, briefly remove then reconnect one main limit wire to display

stored status code. On RED LED boards do not remove power or blower door before initiating

status code recall. After one status code recall is completed component test will occur.


Thanks for Choosing FixYa.


Kelly

Oct 05, 2010 | Heating & Cooling

2 Answers

Osd lockout? How do I get the on screen display unlocked?


OSD Lockout prevents changes being made to the monitor through the use of the front panel buttons. When the OSD is locked, pressing a button from front panel displays OSD Lock-out for about 10 seconds. You can quickly remove the OSD Lockout message by pressing a front panel button again. To unlock the OSD, press and hold the Menu button until the Main menu displays, about 10 seconds. To lock the OSD, press and hold the Menu button until an OSD-Lockout message displays, about 10 seconds.

Dec 03, 2009 | HP W1707 LCD Monitor

2 Answers

Channel lockout on Regency D300 scanner


While in SCAN mode, enter the number of the channel you want to lockout. To re-activate it, enter the channel number again.

Oct 30, 2008 | Uniden BC72XLT Handheld Scanner

1 Answer

Lighting the oven


Control Lockout (on some models)
Your control will allow you to lock out the
touch pads so they cannot be activated when
touched or cleaning the glass panel.
To lock the controls:
Touch the 9 and 0 touch pads at the
same time for 3 seconds until the
control beeps twice. The display will
show LOC continuously and the time
of day if not blacked out.
NOTE: All cooking and timing functions will be
cancelled when locking out the control.
To unlock the control, touch the
9 and 0 touch pads at the same time
for 3 seconds until the control beeps
twice, and LOC will be removed from
the display.
NOTE: Some models have a Control Lockout
pad. Touch and hold it for 3 seconds to
lock/unlock.
Gas/Control Lockout (on some models)
Your control will allow you to lock out the
surface burners, oven burners and control
panel so they cannot be activated.
To lock/unlock the controls:
Turn all surface burners off.
Touch and hold the Gas/Control
Lockout pad for 3 seconds until the
display shows LOC ON.
To unlock the control, touch and hold the
Gas/Control Lockout pad for 3 seconds
until the display shows LOC OFF.
When this feature is on and the touch pads
are touched, the control will beep and the
display will show LOC ON.
 The control lockout mode affects all
controls. No controls will work when this
feature is activated.
 The adjustment will be retained in memory
after a power failure.

Nov 30, 2007 | GE Profile Spectra JGBP90 Gas Kitchen...

Not finding what you are looking for?
Kenmore 44102 Front Load Washer Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5470 Answers

Mike Squire

Level 2 Expert

391 Answers

Robert Rankin

Level 2 Expert

338 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...