Question about Canon PIXMA MP620 All-In-One InkJet Printer

1 Answer

Error message B200...Printer error as occured see the manual. I do not have the manual.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Http://www.retrevo.com/support/Canon-MP620-Multifunction-Printers-manual/id/23007ci369/t/2/

the manual is right under the picture you have to download it I hope this helps you
SabiousOne

Posted on Nov 08, 2010

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
rulds2008
  • 3866 Answers

SOURCE: please help, my printer canon ip 3300 has message B200

Okay from canon on this one this is a Hardware Failure there is nothing more that can be done unless you have $50 bucks for the main singal proccesor board that sends the signal from the printer to the computer and vice versa. So a unwavering support indeed I gave but the fix can be expensive would recommend just recycle it and buy a new printer for under $50 buck you can get twice the quality from lexmark!! Thanks and this tech deserves his 4 thumbs up and a pat on the back don't you think? Do it today we earn your respect as techs by your ratings and feedback thanks and May god bless your family during this holiday season!!

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Posted on Nov 24, 2009

SOURCE: I have a PIXMA

Welcome to Fixya

You can try to reinstall the printer drivers. you can download the drivers here


click here for drivers

If reinstalling the printer drivers does not work then try this

unplug the printer power cable. press and hold the power button on the printer for 5 seconds. power the printer back up.


Hope this helps

Posted on Jun 21, 2011

  • 88 Answers

SOURCE: The message says B200, a

Select the item to cancel butan

Posted on Aug 05, 2011

F Victor man
  • 838 Answers

SOURCE: My cannon MX320 printer light

This error refers to a voltage problem within the print head. Usually the fix is a new print AND the main logic board.

Personally i feel its an end of life error and you should consider replacing the machine as the cost of repair is more than it would be to buy a new printer.

Sorry

Posted on Aug 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT TO DO WHEN I HAVE AN ERROR CODE B200. i CANNOT PRINT AS THE MESSAGE IS CONTACT YOUR SERVICE PROVIDER. IS THERE A WAY I CAN FIX IT MYSELF////


Hi Kathleen,

to clear the Canon B200 error code:

Steps for 4+ Cartridge Printers
  1. Remove All Cartridges. Do whatever is necessary to remove the individual ink cartridges from your printer. In most cases this will be opening the lid of your printer and waiting for the cartridge cradle to move into the correct position.
  2. Remove the Printhead. This is easily achieved in most printers by simply lifting the orange/gray locking lever on the side of the cartridge cradle and then gently lifting the printhead from the printer.
  3. Reinstall the Printhead. Gently put the printhead back into your Canon Pixma printer and lock it into position firmly.
  4. Reinstall All Cartridges. Place all of the cartridges back into the printer and close any open doors. This makes sure that your printer is actively examining the reinstalled cartridges and printhead.
  5. Unplug the Printer. Physically remove your printers plug from the wall and leave it unplugged for 5+ minutes. This allows the printhead to cool and all residual electricity to leave the printer.
  6. Plug the Printer Back.
  7. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
Steps for 2 Cartridge Printers
  1. Turn the Printer off. When your printer is in this error state it will not let the cartridge cradle within the printer move. However resetting the printer should clear the error message temporarily allowing us to troubleshoot further.
  2. Turn the Printer Back on Again.
  3. Remove the Problem Cartridge. Whilst the Canon Pixma error messages do not tend to specify which cartridge is causing the problem, you should be able to have a rough idea based upon which cartridge was last replaced.
  4. Install a Replacement Cartridge. As the printhead is part of the cartridge, sadly there is no way to stop the B200 error without replacing the cartridge. I would recommend either installing a new cartridge or a previously used cartridge that you know to be functional.
  5. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
  6. If Necessary Replace the Other Cartridge. If the error persists with the new cartridge, it may be that the other cartridge has developed a fault and is the cause of the B200 support code. If at this point the error remians I can only recommend replacing the other cartridge.

Aug 11, 2017 | The Office Equipment & Supplies

1 Answer

I have an error message B200


Hi Kathleen,

to clear the Canon B200 error code:

Steps for 4+ Cartridge Printers
  1. Remove All Cartridges. Do whatever is necessary to remove the individual ink cartridges from your printer. In most cases this will be opening the lid of your printer and waiting for the cartridge cradle to move into the correct position.
  2. Remove the Printhead. This is easily achieved in most printers by simply lifting the orange/gray locking lever on the side of the cartridge cradle and then gently lifting the printhead from the printer.
  3. Reinstall the Printhead. Gently put the printhead back into your Canon Pixma printer and lock it into position firmly.
  4. Reinstall All Cartridges. Place all of the cartridges back into the printer and close any open doors. This makes sure that your printer is actively examining the reinstalled cartridges and printhead.
  5. Unplug the Printer. Physically remove your printers plug from the wall and leave it unplugged for 5+ minutes. This allows the printhead to cool and all residual electricity to leave the printer.
  6. Plug the Printer Back.
  7. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
Steps for 2 Cartridge Printers
  1. Turn the Printer off. When your printer is in this error state it will not let the cartridge cradle within the printer move. However resetting the printer should clear the error message temporarily allowing us to troubleshoot further.
  2. Turn the Printer Back on Again.
  3. Remove the Problem Cartridge. Whilst the Canon Pixma error messages do not tend to specify which cartridge is causing the problem, you should be able to have a rough idea based upon which cartridge was last replaced.
  4. Install a Replacement Cartridge. As the printhead is part of the cartridge, sadly there is no way to stop the B200 error without replacing the cartridge. I would recommend either installing a new cartridge or a previously used cartridge that you know to be functional.
  5. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
  6. If Necessary Replace the Other Cartridge. If the error persists with the new cartridge, it may be that the other cartridge has developed a fault and is the cause of the B200 support code. If at this point the error remians I can only recommend replacing the other cartridge.

Aug 11, 2017 | Office Equipment & Supplies

3 Answers

Error B200


Get steps to Fix Canon Printer Error Code B200 instantly. Watch below video to learn how to fix Error Code B200 on PIXMA Printer Call now +44-8000465291 for instant Printer help.
Source: https://goo.gl/xskzcB

For 4+ Cartridge Printers:

Step1:-Remove All Printer Cartridges.
Do remove the individual ink cartridges from your printer. This will be opening the lid of your printer and waiting for the cartridge cradle to be placed in the correct position.
Step2:-Remove the Print-head.
This is can be done by lifting the orange or gray locking lever on the side of the cartridge cradle and then gently lifting the print-head from the printer.
Get full Step by click below link

How to Fix Error Code B200 on Canon PIXMA Printers 44 8000465291

Feb 01, 2016 | Office Equipment & Supplies

1 Answer

Why the cartridge does not move when the printer is on. and when i set to print error no. B200 appear?


http://www.canon.co.uk/support/consumer_products/product_ranges/printers/pixma/error_codes/#b200
B200 Error- This could also be displayed as P10 or the orange and green light blinking 10 times Description:

B200 is a service error that can occur due to a hardware failure with either the printer or the print head.
Resolution:
In most instances, a B200 error will require a repair at a Canon authorised repair centre, however prior to sending your printer for repair please follow the steps below to try and resolve this error-
  1. Turn off the printer
  2. Disconnect the power cable
  3. Open the printer cover
  4. Check for any orange protective tape or white polystyrene and remove if necessary
  5. Check that there are no foreign objects in the printer (such as a paper clip) and remove if necessary
  6. Close the cover
  7. Reconnect and turn on
If the error message is still showing, then it is necessary to deliver or send the printer to an authorised repair centre.
If the printer is still under warranty, (generally one year from purchase) and supporting documentation is provided, then a free of charge warranty repair will be carried out.
If the warranty has expired, then any repairs can only be carried out at cost and charges will apply.
You can find the details of your nearest repair centre using our interactive repair centre locator.
If you own a PIXMA PRO-1 please contact us directly as you may be eligible for an on-site repair.

Jan 14, 2016 | Canon PIXMA MP287 ALL-IN-ONE INKJET...

1 Answer

Cannon pixma mg5220 printer, b200 error msg. how do you remove the printhead ?


Error B200: A service error has occurred.
  1. Turn off the printer.
  2. Disconnect the power cable.
  3. Open the printer cover.
  4. Check for any orange protective tape or white polystyrene and remove if necessary.
  5. Check that there are no foreign objects in the printer (such as a paper clip) and remove if necessary.
  6. Close the cover.
  7. Reconnect and turn on.
If the above solution has not resolved your error, the device needs to be send to service for repair.
It can be that only the print head has malfunctions, but mostly it is another defect in the printer which causes also a defective print head. Changing the print head can solve the issue for a couple of weeks, but then the error will occur again.

May 06, 2014 | Canon PIXMA MG5220 Wireless Photo...

4 Answers

Canon Pixma Mp258 B200 Error


My printer is canon mp258 there was an error B200 . how t fix this?

Apr 07, 2011 | Computers & Internet

1 Answer

Switch on and it displays "printer problem b200 refer to manual. The manual is useless what do I do


Unplug the printer for at least 5 minutes to see if it will clear that error message. The b200 error message is referring to the printhead overheating. It is possible that a printhead nozzle burned out while printing a page and ink ran out. No ink flowing through a nozzle can cause it to overheat and damage it. If waiting for the 5 minute power down doesn't do it, you may have to purchase a new printhead and also check to make sure that you have new ink cartridges.

Mar 02, 2011 | Canon PIXMA MP620 All-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA MP620 All-In-One InkJet Printer Logo

2,355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2153 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...