Question about Hamilton Beach Water Cooler with Storage Cabinet

2 Answers

My water cooler won't cool water. The hot is piping hot and the cold is very warm. what should i do?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Check to see if fans are working i just bought a used one and one of the fans was not working and i fixed it and sems to be working

Posted on Feb 16, 2012

  • Reid Procyshyn
    Reid Procyshyn Oct 15, 2015

    Check fans? How is that helpful? How to check? What to do? What did YOU do?

  • Andrea Ordodi Feb 01, 2016

    How I'd like info too

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Is this model 87307? I am looking to buy this dispenser 87307. Pls e-mail me at vmd011@hotmail.com Thanks

Posted on Nov 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the temperture range hot/cold


This machine is energy compliant to an extreme. The installation says to have the water heater set to 120 and when you put the machine on HOT it will be cooler than that because it mixes the hot with some cold. WARM is a little more cold and COOL is mostly cold and some warm, COLD is just plain cold.

Sep 02, 2015 | Estate ETW4400TQ Top Load Washer / Dryer

1 Answer

Hot water barely comes out,


If you switched the feed hoses over and the problem reversed itself, cold has gone from fast to slow useing the hot water pipe and hot from slow to fast useing the cold water pipe then this would indicate a fault in the water supply from the hot pipe. What sort of pressure is coming from the hot pipe when not connected to the machine but filling in to a bucket? Are there any shut off valves before the pipe that supplies the hot water? Are they fully turned on? Any kinks in the feed pipe for the hot water? Has the hot water feed pipe collapsed internally? Change the pipe to check this and not just at the machine side.

Dec 31, 2012 | GE Spacemaker Washer and Dryer Electric...

2 Answers

Hi, I have a '99 Jetta, new body shape, 2.0L 4cyl that only blows warm air now and again. It's usually cold but can go warm for a bit then goes cold again. When it's cold the hoses show the warm water is...


Under the hood on top of the firewall you will see two hoses,check both of these are hot(the cooler one is the matrix return pipe)if return pipe is cold then undo the clip and vent off any trapped air.this must be done when the engine is HOT,so take care.........

Mar 04, 2011 | 2003 Volkswagen Jetta TDI

1 Answer

Cooler not running


Check power to relay. If yes, check compressor is working. If yes, keep your hand on discharge pipe. If it's not warm, cooler is under gas leak. Rectify leak and recharge gas.Thanks.

Jan 24, 2011 | Whynter FX-6SB Free Standing Hot & Cold...

1 Answer

My BMW 318i has had a new expansion tank fitted after overheating and splitting.After bleeding the cooling system it seems as though the bottom hose is not getting hot any suggestions would be welcome


NORMALY THE HOT FLOW ENTERS THE TOP HOSE AND COOLER WATER LEAVE THE BOTTOM HOSE BACK TO THE BLOCK, SO IF THE TOP HOSE GETS WARM THEN THE RAD IS BLOCKED , IF NIETHER GETS WARM/HOT THEN THERMOSTAT NOT WORKING, OR YOU HAVE BLOCKAGE ELSE WHERE, SO REMOVE BOTH HOSES FLUSH RAD WITH HOSE PIPE, (WHEN ENGINE IS COLD) SEE IF WATER FLOWS OUT AT SAME SPEED AS U R FILLING IT, IF NOT ITS BLOCKED, 2ND REMOVE THERMOSTAT AND FLUSH ENGINE OUT, U CAN BUY RAD FLUSH/CLEANER AND TRY THAT,

Dec 05, 2009 | 2003 BMW 330

1 Answer

No heat air is blowing cold


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is worm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest to flush the heater core.

Oct 22, 2009 | 1998 Ford Taurus

1 Answer

Heater not working


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Why is my warm water is cold? The hot is hot and cold is cold but warm is cold.


There is too much pressure on the cold feed, reduce the pressure on the cold by partly closing off the tap on the cold.
Or ensure the hot feed is fully open and not blocked, check if there are filters inline - remove the feed pipes at the washer end and look into the inlet valves - clear if blocked.
The inlet valve is common to hot and cold water with only a small pipe to fill the machine, the cold water is being forced back up the hot water pipe due to the pressure you can feel the pipe cool down after running hot then go to warm, if hot water is flowing the pipe will stay hot, if not then cold is going up the hot pipe.

Jun 28, 2009 | Admiral AW22 Top Load Washer

2 Answers

Cool water comes out on warm water setting.


The water that is coming from the hot water pipes is likely not hot because it cooled down while sitting in the pipes. We had similar issues with hot water not being ready when our appliance needed it. We heard about Redytemp from our plumber. We have yet to have anymore problems with having hot water when needed.

Dec 09, 2008 | Frigidaire FEX831CS Top Load Stacked...

3 Answers

Plumbing - no cold water from cold water tap


Hi blondi_1452,

I'm Harvey the Master Plumber.

Your question is: Why would the cold line water be luke warm?

In 30 years I've seen this maybe 10 times. It is relatively rare. But each time it was a cross connection between the hot and cold water lines. It could be this fixture is close to the hot water heater or the cross cnnection is in a faucet or it is in the way the water lines are piped. Anyway I would have to closely inspect the system while running the water in the fixtures in different combinations. Once the cross is located the easiest fix at this point is installing a check valve at the right point. You might consider utilizing thr Repair Directory to find a repairman. Make sure he has solved this type of problem before.

Feel free to contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber

Sep 14, 2008 | Home

Not finding what you are looking for?
Hamilton Beach Water Cooler with Storage Cabinet Logo

1,696 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hamilton Beach Water Filters & Coolers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Brad Brown

Level 3 Expert

15441 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Are you a Hamilton Beach Water Filter and Cooler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...