Question about Jamo SUB 250 Subwoofer

Open Question

How can I replace the power supply in my Jamo Sub 250? IT HAS BLOWN.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 238 Answers

SOURCE: Jamo 250

hi, there must be this LINE IN socket (ur so called Hole), then on the onkyo, there must be this sub-line out socket, plug one end of the RC socket to the sub out of onkyo , and other to the line in of the sub, its all to do wirth its appropriate inputs and outputs,let me know

Posted on Jan 12, 2008

Ad
  • 151 Answers

SOURCE: JAMO SUB 650

The jamo sub is a fine buy but also look at subs from REL as they can hit hard when needed and are great for music.Now on to your amp,look round the back and you should find a socket marked sub pre out,plug a sub or phono lead into this and then into the input on the sub,this could be marked in or line in,turn up the volume or gain on the sub and also make sure you have the sub turned on in the speaker settings in your amp.

Hope this helps.
Cable guy.

Posted on Jun 27, 2008

  • 73 Answers

SOURCE: Jamo Sub300. No power. No lights

Well it would void the warrantee, but you can take the back panel off and the power supply will only have two leads (3 if grounded) in from the plug, and out to the crossover. It sounds as if you are correct that the power supply is bad.

Charles

Posted on Jan 05, 2009

  • 127 Answers

SOURCE: I have bought JAMO sub 250 subwoofer and Pioneer

Hi,
You don't need such cable, although you can use it if you have one. If receiver has only mono SUB output (as majority of receivers have), you just connect it to the Left socket on the Sub and it will work.

Using the Y cable would probably cause that you will fed the same signal to both left and right sockets, but half the intensity (you would divide the output from receiver by 2). So in the end the Sub would receive exactly the same signal as when using normal straight cable.

Posted on Mar 03, 2010

  • 127 Answers

SOURCE: cant connect jamo sub 250 to marantz SR4001

Use the PRE-OUT SW (subwoofer) output and connect it to the left RCA socket of your subwoofer.

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Jamo sub 250, the R30 was blown. May I know the value of this resistor ? Anyone can help ?


If its still is defective in a corner or in the attic? Maybe you can make info by a KLIPSCH service centre because Klipsch is the owner of JAMO http://www.jamo.com/about/ if you have not find the answer.
Jamo About

Sep 04, 2015 | Jamo Audio Players & Recorders

1 Answer

Jamo sub 250


Internal power? Check fuses. No fuses? Disassemble and check Power supply if it is internal. If it is external, check power supply with meter.;.

Apr 30, 2013 | Jamo SUB 250 Subwoofer

1 Answer

Please help! Jamo SUB 300 subwoofer still blows (0.8A) fuses after replacing a faulty thermistor, despite a high ohms reading directly across AC mains terminals on the board. What is causing the fuse to...


hi,
i have a jamo 250 sub.the blue light is working.when i connect the jack to the left line IN according to the manual it makes a sound as well.but seems not working.is it related to the fuse????i know the fuse box.but i dont know how to remove the fuse to check.pls help me out.my receiver is onkyo tx-sr 608

thank you

ron

Jan 08, 2011 | Jamo SUB300BA SUB 300 Powered Subwoofer...

1 Answer

Cant connect jamo sub 250 to marantz SR4001... how do i do it? any suggestions?


Use the PRE-OUT SW (subwoofer) output and connect it to the left RCA socket of your subwoofer.

Sep 27, 2009 | Jamo SUB 250 Subwoofer

1 Answer

I have a jamo 250 sub and dont know which coax input to use


one will do just fine if you've tried one and its not working try to refer to manual on how to set up in the receiver function menus and if the sub is powered by an external amp which most are

Jul 03, 2009 | Jamo DVR-50 System

1 Answer

Jamo Sub300. No power. No lights


Well it would void the warrantee, but you can take the back panel off and the power supply will only have two leads (3 if grounded) in from the plug, and out to the crossover. It sounds as if you are correct that the power supply is bad.

Charles

Jan 05, 2009 | Jamo SUB300BA SUB 300 Powered Subwoofer...

1 Answer

Jamo 250


hi, there must be this LINE IN socket (ur so called Hole), then on the onkyo, there must be this sub-line out socket, plug one end of the RC socket to the sub out of onkyo , and other to the line in of the sub, its all to do wirth its appropriate inputs and outputs,let me know

Jan 11, 2008 | Jamo D 4SUB Subwoofer

Not finding what you are looking for?
Jamo SUB 250 Subwoofer Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jamo Audio Players & Recorders Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Tom Chichester

Level 3 Expert

35572 Answers

 Grubhead
Grubhead

Level 3 Expert

5151 Answers

Are you a Jamo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...