Question about Denon AVR-3805 Receiver

1 Answer

Hi it sam again

Thanks again for yesterday
have you got any suggestions on were i could get a component diagrams so i what im meant to take out and soldering
or if you could give me sum in site i would grateful

Posted by on

  • sam pomery Jun 16, 2008

    thanks agian

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers

This is the site where you to go www.schematicsonline.com / www.smshop.org / www.free-manuals.com /www.sharefx.com / www.icxinyi.com ;then page DENON AVR 1706 7.1 channels

Posted on Jun 15, 2008

  • LORETO LACARON
    LORETO LACARON Jun 17, 2008

    no problem..thanks for your rating if u have problems in the future dont hesitate to ask my advice...see ya!!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help with the schematic diagram of a JVC RX-5THPBK power amplifier


Have you checked into SAM'S FOTOFAX or other searchers, or do you have schematic and need interp. of it?

Aug 03, 2016 | JVC Audio & Video Receivers

1 Answer

Tx-ds777 no sound from front speakers on a speakers work on b but if I run a and b the center and surround stop working


Hi MJ, If you run your B speakers you will drop your 2 surrounds as the B speakers are meant to be used in a different room. I would suggest that you give us a call so that we can try some troubleshooting, please call our Product Support Team at 800-229-1687, Thanks, JT

Aug 19, 2015 | Onkyo TX-DS777

2 Answers

Im looking for a wiring diagram for a Baldwin electric Organ D-911


I have the wiring diagrams for this organ. Contact me and i'll figure a way to get a copy of what you need to you.

Aug 21, 2010 | Audio & Video Receivers

1 Answer

Pioneer Elite vsx-27tx receiver with no bass!?


There may be a subwoofer mute function on your amp. The sub out is nothing more than a preamp output with a low frequency response. It is meant to be amplified by an external amp. Either check your powered subwoofer for operation or look through your operators manual for a sub mute function.

Feb 11, 2010 | Pioneer VSX-27TX Receiver

1 Answer

Receiver will not turn on.


check all speakers and wire not short ....if sam problem unit power ouptup amp need replaced

Nov 07, 2009 | Audio & Video Receivers

1 Answer

NAD T773 Shuts Down in 1-5 secs


Your problem is a common symptom of loose connection or cold solder and cleaning problem this is the main caused of no sound or automatic shut off for how many seconds..Cold solder issues - each component is soldered into small holes on the printed circuit board which in turn connects said component to the other components. Due to time, heat, use, some solder joints would be cracked or loose. It is possible that the cold solder is still minimally connected (hanging by a thread). When the receiver turns on heat would be generated which would be sufficient to further loosen up the solder joint to the point it no longer provides electrical contact. Jarring the unit creates movement inside enough to re establish the contact, sometime good enough sometimes not enough. Again, since the unit still operates (sometimes) then it is highly probable that there are no defective components. As you have surmised, it is possibly a loose connection, solder joints are "connections" except that molten soldering lead is used to attach/connect the component to the board, "loose connection" in this sense is equal to "cold solder". Again on the assumption of no defective parts, then seeking a more experienced buddy for the soldering might be to your advantage. This is of course in addition to the possible electrical hazards when repairing.... Good luck: Regards, VOTIT

Jun 08, 2009 | NAD T773 6.1 Channels Receiver

1 Answer

I have a relatively new (less than 3 months old) Harmon Kardon Receiver HK3490. It turns on but immediately turns off. You can hear a clicking sound like a breaker is disengaging. The problem started...


It is a relay clicking. You will need to obtain a schematic to troubleshoot this but they are available online. The protection circuits have been degraded from the short circuit but it is still alive and the discrete components are easy to replace. I used to use Sam's Fotofax but googling your HK model will get you alot of results. Harmon Kardon is a great brand and definitely worth fixing. ~Steve Medley

Nov 08, 2008 | Audio & Video Receivers

1 Answer

1st time using component video connections on my onkyo


Yes, switch to the video input that you are trying to configure (i.e. video 1-4). Press the menu button on the receiver or the remote and cycle to video settings. There should be a setting that says "video output" or "output" - set that to component. You may also have to configure the Input for that particular setting. For instance, if you have an HD tivo going into component 2 but you want it to be Video 1. Select Video 1, hit the menu button and scroll to video setup. Select video input setup and cycle it to component 2. Next, use the menu to cycle to video setup, select video output, switch to component. This should solve your problem. As a sidenote, you may also have to configure the audio in/out if you're using digital coax or optical. Let me know if this works.

Feb 02, 2008 | Onkyo TX-DS787 Receiver

1 Answer

Sherwood RD-6500 sound problem


I don't have this particular reciever, but I think the dubbing feature mentioned can be turned off. If that can't be done I suggest moving the components in video and audio 2 to the 3rd available one, it shouldn't have that feature. That's all I can offer.

Jul 18, 2007 | Sherwood RD-6500 Receiver

2 Answers

Video out problem


hi there might be a protector circuit and then it needs only a reset OR the amplifier and a couple of diodes have been shorted the fix can be very cheap (reset) or very expensive (depends if the amp itself is burned) in any way you got warranty!! (it wont work if you will say that you didnt hook it right....) good luck

Feb 23, 2006 | JVC RX-884V Receiver

Not finding what you are looking for?
Denon AVR-3805 Receiver Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

jonpoint

Level 1 Expert

4 Answers

Tech Leprechaun
Tech Leprechaun

Level 2 Expert

61 Answers

Are you a Denon Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...