Question about Electrolux Vacuums

1 Answer

The chord will not recoil - Electrolux Vacuums

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 694 Answers

Try standing it up and gently pull on cord and release. It may rewind after a few tries. If it does fine, then just be careful how far you pull it out.
If it still won't rewind, you need to take it to an authorized Aerus Electrolux store and have the service tech have a look. There are a few things in the rewind assembly that could be causing it not to.

http://www.aerushome.com/storelocator/

Posted on Nov 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 mtd yardman pusher lawn mower.Need complete recoil starter assembly


order it online Im sure that the parts should be available through briggs and stratton or yardman inc

Jun 28, 2014 | Dewalt Vacuums

1 Answer

Riccar 1700 melted connector to circuit board...


It might be an easy fix but should be done by a qualified Riccar dealer.

Jun 03, 2013 | Riccar Vacuums

1 Answer

Cord recoil


what model is it DC?

Mar 10, 2013 | Dyson Vacuums

1 Answer

Have just purchased vax c90 vacuum cleaner,have a problem re-coiling the power lead.have followed instructions to press down on designated button,but power lead does not recoil.


On pressing the cord has to coil into the holder and if this wont happen there is some mechanical fault in the recoiler or spring.
You can pull the power cord once again outside and let it slide inside, repeat this sequence to allow the winder to respond and then it might pick up.

Apr 06, 2011 | Vacuums

1 Answer

I had to replace the recoil assembly on Electrolux 2000. Recoil works fine by it-self but when vacuum is reassembled the recol does not recoil. Why?


You have assembled it incorrectly and the recoil unit is sticking against something preventing the recoil. It is still tensioned ? Have you checked?

Feb 02, 2011 | Vacuums

1 Answer

Had a bad place on the chord about 6 feet from the end, cut the chord back to that point, put on a new plug but now it won't turn on. Is there a reset switch or fuse somewhere?


Yes, there is. It's a small white button located near on the back, near the left wheel. Unplug vacuum, then use the end of a paper clip to push in and reset.

Aug 12, 2010 | Riccar 8955 Upright Vacuum

1 Answer

How do I get at the power cable recoil mechanism on a Dyson DC02 Standard Cyclone Cleaner?


Go to www.dysonmedic.com then scroll to the bottom of the page and click on "DC02 cable replacement". You will find detailed instructions AND pictures! Can't do better than this.

Aug 10, 2009 | Vacuums

2 Answers

Dead Miracle Mate Vacuum cleaner


You don't have to open the cannister. You can easily remove the black plastic collar through which the cord is supposed to emerge. The collar has a little springy tab that holds it in place. Once the collar is removed, you can reach in and grab the cord and pull it out.

Steve

Aug 02, 2009 | Vacuums

2 Answers

Hoover Fusion Cyclonic


Ok, lfitz, I fixed my problem. First I called the Sears Service Center. They told me that I would have to drop it off there, and they would send it to Orlando to get looked at. The whole process would take about 2 weeks and who knows how much money. So I decided to become my own Hoover technician. It turns out that my original diagnosis was right about the chord that electrically connects the power on/off switch at the top of the handle to the rest of the vacuum. This was extremely easy to fix so please don't be scared away, although it does require a little philips-head screwdriver action. As always, make sure the vacuum is unplugged before you start. On the back of the vacuum, there is the hook that you wrap the electrical chord around for storage (the top one). On either side of that hook are two screws. Unscrew those. Now, the small piece of plastic that has the hook on it can be carefully pulled back, or removed if you need to. Inside, I found the detached end of a coiled black electrical chord that looks kind of like an A/C adapter. This chord should be plugged into the bottom of the metal shaft that slides in and out to allow you to adjust the height of the handle. Now, adjust the metal shaft so that you can plug the black chord back into the base. Push the chord in until you hear it click. Now, put the plastic piece back in place and put the screws back in and you're done. Plug it in and give it a try. I hope this helps.

Dec 16, 2007 | Hoover Fusion Plus Cyclonic Upright Vacuum...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18387 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Mack Baxter

Level 3 Expert

381 Answers

Are you an Electrolux Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...