Question about Crunch Drive V-600 Car Audio Amplifier

2 Answers

Crunch GP 3000 D Pro

Yes I was playing that amp on my subs and i turned the volume up about 35 and it went in protect mode. I done with Book said do if goes in protect mode by unpluging rca cables and then still dont work unplug speaker wires i did that all still doesnt work. I even undone the power and let set about 10mins and still comes on. I pulled cd player out and undone the plug and then pluged it back in and it played subs for like 1 sec then went back in protect mode. The subs arent blown and I have no clue what to do to get it out of that protect mode. Thanks

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 631 Answers

It's very likely that the output transistors have failed in the amp. They will need to be replaced.

Posted on Jun 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a hifonics Zrx1200.2 amp. I am running 2 Rockford fosgate p3 12s with it. The specs on amp and subs match perfect. So I have everything wired correctly, it least I sureeee think so. Subs are dvc...


u could just not have enough battery power or the load on the amp is to much. if the amp is in stereo mode it should work but if it is in bridge mode the ohms would be to low .. best thing is to get a sub amp with a 1 ohm stable capacity.. and you amp should be at least one third more powerful than the subs..eg: if the 2 subs is 1000 w each the the amp should be 2500 rms and up to prevent the amp from maxing out and over heating etc.

Jun 09, 2013 | Car Amplifiers

1 Answer

My ph5000d plays until i turn it up then it cuts in and plays then to protect mode back on why dose it do that its just when i turn radio up


Ok because your wattage is too high for the amp when adjusting a amp with speakers always start like this turn amp gain all the way down head unit bass all the way down and treb all the way up then turn on ur highest listening volume that u like then ajust amp to that hight if will stop protect from happening if continues ur sub is too many watts for amp ok

Dec 13, 2012 | Car Amplifiers

1 Answer

I have a bamf 5500 series and the amp is on and working but when i turn up the volume the amp will go into protect mode and stay there untill i turn the volume back down then the amp comes out of protect...


you probably have a blown sub(s) that short out when the volume is turned up. it would be a good idea to find out which one(s) is bad and replace it. sooner or later it may make the amp go bad if not replaced or removed.

Jan 06, 2011 | Power Acoustik BAMF5500/1D Car Amp

1 Answer

Protection light comes on , was only coming on when i turned up the stereo , now it stays on , all the wires are good and i cracked the amp open and nothing looks burnt


check your gain on your amp. If it gets hot the shuts off into protection mode you are over working your amp. Check to see the way your subs are wired up and see if your amp can handel the load.

May 20, 2010 | Crunch Drive V-3004 Car Audio Amplifier

1 Answer

My amplifier is not in protection mode everything works fine but my subwoofers play a very small sound . and it is not my subs at fault i already tested my subs and they work fine. i know theres a problem...


THERES A PROBLEM WITH YOUR RCA'S,IF YOU JIGGLE THEM WHILE THERE HOOKED UP TO THE AMP AND THEY MAKE THINGS LOUDER OR POP THAN YOU NEED TO GET THE RCA TERMINALS FIXED.

May 07, 2009 | Crunch Maxxsonics PZi 3000.1D Car Amp

1 Answer

My car amp wont come out of protection mode.


hey i had this happen to me, pull the deck out and move the rca cables to a different channel and see if that does not fix it. i blew out my sub pre out channel in my deck and had to use the rear pre outs. try this and let me know what you come up with. good luck

Mar 07, 2009 | American Pro Car Amplifiers

2 Answers

Kicker zx1000 only plays at low volume


how high did you turn the gain up and or the freq. mode most soun good at 90to 120hz. any higher some amps trip, and your speakers may not be able to handel the amp.

Jul 20, 2008 | Kicker ZX10001 Car Audio Amplifier

2 Answers

My amp goes into protection mode at high volume


need more info, make and model of amp and subs please

Feb 18, 2008 | Kicker DX350 Car Audio Amplifier

3 Answers

Red LED "Protection Light is on" What is the problem


The red light means the amp is in protection mode. A few things can cause protection mode..... First disconnect the subs completely from the amp, and turn it on, if it powers up you have blown subs. Also try checking the main power wire at the battery...sometimes the current your meter is seeing is backfeeding from the remote wire, so your main power line could be blown at the fuse under the hood. hope this helps

Jul 17, 2007 | Crunch BlackMaxx BMX2250 2 Ch 1000W Amp...

Not finding what you are looking for?
Crunch Drive V-600 Car Audio Amplifier Logo

974 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crunch Car Amplifiers Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Are you a Crunch Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...