Question about Sony Televison & Video

1 Answer

I replaced the projector lamp. but no matter what I do, I still get the red lights blinking

Posted by on

  • 1 more comment 
  • tom BURG Nov 05, 2010

    It's a Sony WEGA, model KDF-55E2000, projector lamp XL-2400. I am getting 3 red lights blinking every 5 seconds

  • tom BURG Nov 05, 2010

    The model number is KDF-55E2000, projector lamp #XL-2400. I get 3 red lights blinking every 5 seconds.

  • tom BURG Nov 05, 2010

    I removed and replaced and locked the cover in so many times I can't remember, but I still am getting the red lights. Any other ideason how to fix this, so the TV works?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,594 Answers

Hi,
I just replied this question, let me know Sony tv model number and how many times its red light blinking to sort out its problem.
Your reply is awaited.
Thanks.

Posted on Nov 05, 2010

  • 2 more comments 
  • Shahid Electronics
    Shahid Electronics Nov 05, 2010

    Thanks for info.
    3 times red blinking indicates that lamp cover (plastic cover) has not been fixed back in its position properly.
    Make sure lamp cover is put back securely then turn On tv.
    Lamp cover push a safety micro switch inside that sends signal to system control chip to turn On tv.
    Let me know if you have additional question.
    Thanks.

  • Shahid Electronics
    Shahid Electronics Nov 05, 2010

    Yes, next thing that needs your attention is safety micro switch that being pressed by lamp cover. In my opinion that switch is got broken and need to be replaced.
    Click HERE to view switch image and price info.
    Thanks.

  • Shahid Electronics
    Shahid Electronics Nov 05, 2010

    Click on thumb nail image on that page to have enlarged images of micro switch board.

  • Shahid Electronics
    Shahid Electronics Nov 05, 2010

    I hope following image will help you to locate T1 Board in KDF-55E2000


×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Sony projector 3LCD lamp/cover blink red


When I plug the LCD the LAMP/COVER flsh blinking red light

May 28, 2012 | Sony Office Equipment & Supplies

2 Answers

Red power, blinking red temp


Hi,

if the Lamp error and Temperature error lights are flashing red this means that there are two separate errors.

  • A flashing lamp light means the lamp failed to ignite. It could be a lamp driver problem or lamp failure. Replace the lamp to resolve the issue. If the issue is not resolved, then service the projector.
  • A flashing Temperature light signals a fan error. Turn the projector off and allow it to cool down. If the light is still flashing after the projector is turned back on, service the projector.
Goodluck..

Feb 25, 2008 | Hitachi CP-X250 Multimedia Projector

3 Answers

Status light is blinking red, power button orange nec vt700


Hello
Look at the number of blinks of the status light.
[1] If it blinks at one cycle (0.5seconds On and 2.5seconds OFF) : Lamp cover error or lamp housing error. Replace the lamp cover or lamp housing correctly.
[2] If it blinks 2 cycles (0.5 seconds ON and 0.5 seconds OFF): Temperature error. The projector is overheated. Move the projector to a cooler position.
[3] if it blinks at 4 cycles (0.5 seconds ON and 0.5 seconds OFF): Fan error. Fans sill not work correctly.
[4] If it bliks at 6 cycles (0.5 seconds ON and 0.5 seconds OFF): Lamp fails to light. Wait a full minute and then turn on again.
[5] If it blinks continous (Red): Lamp has reached the end of its life. Lamp replacement messege will be displayed. Replace Lamp with same type and number. After replacement reset lamp hour. OK.

Sep 10, 2011 | NEC VT700 Projector

1 Answer

New lamp is placed in tv, but tv won't come on. Light in front of power button is blinking green, then blinks red. Not sure what the problem is


One question, why you decided to replace lamp in tv? Did tv showed red lamp light blinking?
Suggestion, make sure lamp cover has been placed back in its position after lamp replacement, lamp cover is first thing that you removed from tv cabinet to take out lamp.

Oct 05, 2010 | Sony XL-5100 Projector Lamp for Grand WEGA...

1 Answer

My lamp light stays on my status blinks


if it's blinking red, how many times? 1 time- lamp cover. 2 times- overheating. 4- fans. 6- lamp. if the lamp led is lit red, replace the lamp.

Dec 09, 2009 | NEC VT460 Multimedia Projector

2 Answers

Blinking red light


replce lamp ballast board of your projector...

Oct 06, 2009 | Epson EMP 7500 Multimedia Projector

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

74887 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...