Question about Lexmark Wheelwriter 1000 Typewriter

1 Answer

Won't type. blinking 1 and 2 lights. Beeps 6 times when you turn off and on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexmark Master
  • 3,594 Answers

The keyboard is going bad. You can try my tip under WW1000 or contact Geo. Beters Co.
@ 800392-8085 for a KB rebuild. Tell them O'Reilly sent you.

DickyO

Posted on Nov 05, 2010

  • Kyle Vorhis Jun 12, 2012

    Its the main pcb not keyboard

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sonic scooter will not go,first turn on status light blinks 1 time then 2 times, 1 time then 2 times then 3 times then 1 time 3 times then 1 time and continues that 3 and 1 blinking, what can I do?


Test batteries to see if they full, the controller thinks either you need to charge the batteries or it is over charged. 2 beeps need charging, 3 beeps overvoltage.

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Sep 28, 2015 | Sonic Health & Beauty

1 Answer

2001 jag won't start. Security light is blinking


the problem you have is caused by the pats anti theft system is not recognising your key it may be the transponder or you may need a new key and get it programmed by a jag dealer or someone with the needed gear to do it with best advise take it to a jag dealer

Aug 13, 2017 | 2001 Jaguar S-Type

1 Answer

I have an IBm Wheelwriter 5 typrwriter. When I turn it on the line space lights blink and I cannot type or get the casette to move at all.


How many beeps? Which Lights? Blinking together or sequentially? These will help to determine the problem.


DickyO

Aug 04, 2011 | IBM Wheelwriter 6 Typewriter

1 Answer

The spacing lights


Check to see that the printwheel is properly installed, then check for debris in the P/W area.

DickyO

Mar 26, 2009 | Lexmark Wheelwriter 6 Series II Typewriter

2 Answers

Typewriter only beeps and lights blink. Nothing else.


the beeping and the lights are error codes, meaning the machine will need repair

Feb 25, 2009 | Lexmark Wheelwriter 30 Series II...

1 Answer

IBM Wheelwriter 6 Series II beeps


Three beeps and the space lights blinking means the batteries are bad replace them and be sure the holder is clean.

DickyO

Feb 14, 2009 | IBM Office Equipment & Supplies

2 Answers

Wheelwriter 15 series II


The ribbon drive motor might be n/g. I think 6 beeps is the ribbon motor located under the gear on the ribbon cartridge.

Feb 08, 2008 | Lexmark Wheelwriter 1500 Typewriter

1 Answer

Beeps 6 times, lights blink


The prinwheel sensor is likely the issue.  Move the carrier to the right, on the left side of th carrier toward the rear of the machine there should be a small black "flag" sticking out of the carrier.  this should move freely in and out if it is not there or does not move the machine cannot detect the printwheel the sensor will need to be replaced.
  You ca also check for debri down in the area where the printwheel sits.

Sep 11, 2007 | Lexmark Wheelwriter 1000 Typewriter

1 Answer

Six beeps of the standby light...


Yes your suggestion is correct. This type of problem occurs due to humidity also. Solution is if your a technical person or service person just remove main pcb from the tv and blow all dust and clean it. Check whether the dry soldered in power supply area and jungle ic area. if found clear it. Now the tv is working well and good. 6 times blinking means problem in jungle ic area.

Aug 23, 2007 | Sony FD Trinitron WEGA KV-27FS100 27" TV

Not finding what you are looking for?
Lexmark Wheelwriter 1000 Typewriter Logo

Related Topics:

541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Don  Farrell
Don Farrell

Level 3 Expert

1018 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...