Question about Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

2 Answers

Keymaster Remote Pad does not reprogram The instructions say to type in my code, hold down zero, then press ENTER. The opener lights are supposed to flash but they don't. I've tried proceeding to enter the new code anyway, but it is still the old one that works. What else can I do?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,197 Answers

Try it this way.

Locate the smart/learn button on the rear of the motor unit near where all those white wires go. Press and immediately release this and then walk over to the keypad and key in any 4 digit code you like and press enter.



Posted on Nov 04, 2010

  • Gary Tompkins
    Gary Tompkins Sep 05, 2011

    I so want this to work... but it doesn't on my brand new opener. I have tried it a dozen times as well as just holding the Enter key. I've reset the Learner (and had to reprogram my two transmitters, which did fine). The keypad just won't get learned... no lights blink on the opener. Any more thoughts, ideas on this? Thanks!

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to reprogram ve remote pad thank

Posted on May 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trying to reprogram my 387lm to my 8550 liftmaster


Its not compatible with an 8550 of it has a yellow learn button....you will need to locate an 877max lm keypad

If you need further help, reach me via phone at https://www.6ya.com/expert/casey_35b114d22660c612

Apr 11, 2013 | Chamberlain Liftmaster 387lm Wireless...

2 Answers

Tried to reprogram security code for outdoor key pad on 1/2hp craftsman garage door opener according to instructions online, pressed learn button- put in new 4 digit code-held enter. Lights did not flash...


Seems you've done everything right. Press and immediately release the smart/learn button and then walk over and key in a 4 digit code and press enter. If you are sure the battery in the keypad is good then I think your keypad is on the fritz or the wrong one for that opener.

Apr 19, 2011 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Can't reset remote keypad


Press and immediately release the SRT button and then walk over to your keypad and key in any 4 digit code you like and press enter.

Aug 25, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Recently i replaced the battery to my keyless pad and i was succesful in re-programming it. The problem that i am having now is the garage door will not move when i enter the new programmed number on the...


You need to reprogram. Press and release the Learn button and within 20 seconds type in 4 digit code and press and hold enter. The light on the opener should flash once or click if you have no light bulb. This should solve your problem

Jan 28, 2009 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Reprogram a keyless entry remote


Hello
this is how to program the remotes/keyless entry

How
  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk

Jan 13, 2009 | 1995 Lincoln Town Car

1 Answer

My pad, when I put in pass code #, will not open my garage door from the outside.


simply reprogam keypad. Press and release learn button and the press the 4-digit code and press and hold enter until light flashes on motor,

Sep 18, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Garage door keypad & remote


You need to sync both. I have a LiftMaster. If you want to change the code on your keypad you need to open up the garage door motor compartment where the light is (mine is in the back). Press the learn button, within 30 seconds enter the new code on your keypad and hold down the enter button for several seconds until the light on the opener blinks to tell you it has learned the code. Test the new code to see if it works. If the new keypad code works, then try the remote. My remote will not work after I reprogram the keypad. If the remote does not work (check battery) then climb back up the ladder and press the learn button on the garage door motor again, press the remote button and hold down until the light blinks again and the opener has learned the new code. This process works when I need to sync my remote and keypad. Good luck, I hope this helps.

Jul 21, 2008 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Regional code


open tray
Press PAUSE
enter 0000
The region code set page should appear.
Set code. 0 for multi region
Press PAUSE.
OR

Make sure your TV is on and the DVD player is active on it
Unplug the DVD player
plug it back in
wait for text "nodisc" to appear on the DVD display
Use remote control to open tray (tray must stay open)
Use remote control to Press "Pause" (you won't see anything)
On the Remote control number pad enter the number "0000" (4 zeros)
The region code setup window will appear on your TV
on the remote control number pad enter number "0" (zero)to set multi region
Use remote control to Press "Pause" again
close tray

Jun 06, 2008 | LGDVB418 DVD Player

9 Answers

Trouble changing passwordon model 940CB wireless keyless entry


easyer then that , you die! Open your garage door, take out the step ladder, a chair or get up on *********** in law's back, (here's your chance to be on her back for a change) press the read button of your unit (motor) a led should light up and on the key pad, key in the new 4 digits code and press enter, the light of the unit should blink javascript:; Post Solution

May 19, 2008 | Sears Craftsman LiftMaster Chamberlain...

3 Answers

Remote


Sanyo codes for brightstar remote: 620, 801
Press and hold set up button until light comes on then enter one of the codes and it should work.

Mar 11, 2008 | Universal Remote Control Remote Control

Not finding what you are looking for?
Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+ Logo

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sears Building Materials Experts

Glenn Mayer
Glenn Mayer

Level 2 Expert

91 Answers

Mike

Level 3 Expert

4354 Answers

Cindy Wells

Level 3 Expert

5528 Answers

Are you a Sears Building Material Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...