Question about Pitco Frialator SG18S Deep Fryer

1 Answer

Programing new control board on sg18

Need help setting up new controler for SG18

Posted by on

  • Factory boss Jun 18, 2008

    thank you fossilruins, that's just what I was looking for,I appreciate the help.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 114 Answers

This is the operating manual for the SG18S, it talks about programming the electronic controller:

http://www.pitco.com/PDFs/manuals/SG-SGH-Solstice/L20-206.pdf

Posted on Jun 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do u program a new button for time? We have been introduced a new item that only needs to cook for 1 min & 30 seconds & were not sure how to do this. Model # SCFD350GNCS Serial # 0904TS0005


It will depend on which computer configuration you have on your fryers.
You can download this manual from frymaster to help, it contains all programming instructions, just find the computer/controller you have and follow the steps.
Computers Operation Manual from Frymaster.com

Jun 08, 2011 | Frymaster Dean Frymaster/Dean FPEL3 Deep...

1 Answer

Why does my Pitco Frialator not heat to 350?


If your fryer has computer controller (the one with 8 product buttons and left, right arrow), check the display when you turn off the computer board, it should display "gas 2". If not, you have to change the gas configuration by accessing the programming mode.

Feb 24, 2011 | Pitco Frialator SG18S Deep Fryer

2 Answers

I have a pitco 5 fryer frialator. 3 of them are sg14 and 2 are sg18. It has a built-in filter system. Currently, the filter motor is not turning on when the red lever is pulled out. We've reset the unit...


Most probably, there is a clogged portion on filter pipe. You have to clear the clog so that the motor can run without tripping the electrical system.

Sep 27, 2010 | Pitco Frialator SG14 Deep Fryer

1 Answer

My pitco frialator chips fryer diplaying CFG error


CFG error on controller board can be cleared by resetting the controller back to factory setting and by doing this, all program added after the factory setting will be erased so you have to reprogram them again.
Programming guides are downloadable at PITCO site on http://www.middleby.com

Jul 29, 2010 | Pitco Frialator SG14 Deep Fryer

2 Answers

Hi actually i have a cifs40 deep gas fryer and recently i change the control thermostat,now when turn the pilot on ,after 15 second the pilot stay on,but when turn the control valve knob to on position...


Hi, from the above question, the problem is not with ht thermostat but with the control board. The control board fails to hold onto power when the device is heated up, that why it goes off automatically..

Take care

Apr 26, 2010 | Imperial IFS40 Deep Fryer

3 Answers

High limit kicks out fryer and pilot light can


Since you've mention the pilot light goes out at 400 degree F, then we are talking a gas Deep Fryer. The deepfryer usually use at 350 degree F for chips or else. Because the oil will start breaking down its quantity of frying very quickly over that temperature. Most people set at 350 degree F. Now we comes back to your problem, First you should have a deep fryer thermometer they espcially made for deep fryer, (You only mention 400 or better ) that make me think you're only guessing. Knowing the temperature is very important, most Hi limit is set at 420 degree F.
To me it seen the Hi Ltd control is working and that is why it cutting out the pilot when it reach its limit but we don't know what temperature that when the hi limit cutting out at.
When you have a thermometer, put it in the cold oil and turn the temperature to 100 degree F to see what the temperature control cutting out at. slowly increase your setting until it cutting out at 350 degree F . If you set at 250 degree F and the thermometer already reaching 350 degreen F then don't go any further , your temperature control is defective and need to be change a new one.
This is only the first step, you still have to check out the Hi ltd control to see how good its condition is,so far your information say it cutting out at 400 or better. But you've to be sure, because it is a safety control. Hope that will help you , God Bless.

Jul 05, 2009 | Pitco Frialator SG14 Deep Fryer

1 Answer

Pitco Frialator Model 14R digital controller panel reads "P"


Your controller is in a program mode ! To exiit program mode you will need press and hold the P button for 5 seconds to exit programming.

Scoota

Dec 01, 2008 | Pitco Frialator SG14 Deep Fryer

2 Answers

Need to know the value of a resistor


Tim, I am a commercial hvac, refrigeration, and commercial kitchen equipment mechanic. I have rebuilt many of those units. While the notion that all it might be is a 20 cent resister is noble, you are forgetting that this particular circuit has been in service in airborn oil, dust, moisture, spices AND MORE THAT attack ELECTRICAL/ELECTRONIC/COMPUTERIZED equipment.

After many years of repairing vrs replacing, the failure rate was so high in other components and circuits that I realized it just wasn't worth it. Its NOT JUST THE COST OF SERVICE AND PARTS, but also THE DOWNTIME AND LOST SALES you need to take into consideration as well.

Take it from a professional, REPLACE THE BOARD!!!

Nov 11, 2008 | Frymaster Dean MJH50-SD Deep Fryer

Not finding what you are looking for?
Pitco Frialator SG18S Deep Fryer Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pitco Frialator Deep Fryers Experts

starztruck4u

Level 2 Expert

77 Answers

Treefrog15
Treefrog15

Level 2 Expert

126 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Pitco Frialator Deep Fryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...