Question about Black & Decker 3/8" Variable Speed Reversing Drill Kit" [Misc.]

1 Answer

I replaced the carbon brush yet does'nt work. what is the problem all seem look all right

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check the cable

Posted on Nov 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need brushes for a 111409-01 branch wizard


Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, overheating or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

May 03, 2014 | Remington Electric Chain Saw

1 Answer

Are brushes available for remington 106890-02


Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

Nov 06, 2013 | Remington Electric Chain Saw

1 Answer

Hoover se147 washing machine, wont spin at all , it will fill and drain. Have checked pressure switch and appears okay. Have also had circuit board out and that seems okay.


Have you checked the carbon brushes within the motor, chances are they are worn. you will need to remove your motor to get to the 2 carbon brushes.these will be in a plastic casing, held in place by 2 screws. There is just 1 wire going to each brush. When brush is removed, the carbon should be at least 20mm long. If not replace with new

Aug 13, 2011 | Washing Machines

2 Answers

Problem is my hardly used Toro Blower Vac is getting no Power


If it has not run for awhile, check the brushes. they might need to be replaced. The plug is usually moulded right on power cord. That might have to be replaced because if there is a problem with a broken or disconnected wire right at plug there is no way to see it. Hope this helps.

Dec 07, 2010 | Toro 51599 Electric Blower 12 Amp

1 Answer

Washer drum does nt rotate


You need to replace the carbon brushes on the motor. Below is a link to the part.
http://www.appliancepartspros.com/part_details.aspx?part_id=2822714

Nov 25, 2010 | Bosch Axxis WFL 2060 Front Load Washer

2 Answers

The switch of the saw is not working 00


You need an AC voltmeter to trace the problem with the switch. It can also be a bad motor brush/spring--these saws are great for killing motor brushes, and there are virtually no replacements available as Remington has ceased saw operations. If it is a bad brush, visit an electrical tool shop to see if they have something that will work from a different brand of tool. Good luck!

Jun 28, 2010 | Remington 16" Electric Chain Saw

1 Answer

WD62 is not spinning even after chaning new carbon brushes


when u changed the carbon brushes did u move the little metal pin to free the carbon off it must be able to come out then in with ease if not do this if u did then if the carbon brushes have got too low then it will have more then likely damage your motor m8

Feb 09, 2008 | Hotpoint WD62 Front Load Washer / Dryer

1 Answer

Kirby G5 - Stopped


The carbon brushes in the motor need to be replaced. Very IMPORTANT....... DO NOT run the Kirby anymore until you get this fixed. If you do, the armature will be in danger of being damaged. (and that part is expensive!) The carbon brushes are reasonably priced, and you can use this online guide to get to them and change them. It's a guide for replacing the power switch, but it will help you change the carbon brushes too. Hope I've helped...
Marci

http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018

Nov 07, 2007 | Kirby G5 Bagged Upright Vacuum

1 Answer

Washer doesn't reliably spin dry clothes


more than likely your carbon brushes which are situated in your motor locatable by a single wire on each side of your motor going into a plastic casing that holds the carbon if it doesnt have carbon brushes than it will have a module which is about 4in in length and is a circuit board this will need replacing which in some cases is not cheap at all

Aug 15, 2007 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Black & Decker 3/8" Variable Speed Reversing Drill Kit" [Misc.] Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Drills Experts

JOHN LAPIER

Level 3 Expert

2528 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Robert Monigold
Robert Monigold

Level 2 Expert

390 Answers

Are you a Black & Decker Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...