Question about HP PSC 1610 All-In-One InkJet Printer

1 Answer

Receiving Error: 0x8392b78c 1: What does this mean?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • HP Master
  • 7,733 Answers

Do this:

  1. Without turning off the product, disconnect the USB cable from the rear of the product.
    NOTE: The USB cable connects to the port on the back of the product. The port is labeled with the USB icon (Receiving Error: 0x8392b78c - c01424575.gif ). Figure 2: Example USB connection (your product might not look exactly the same as this example)c01651067.gif
  2. Remove the cartridges from the product.
  3. Wait for the 'Insert Cartridges ' message to display on the control panel.
  4. Disconnect the power cord from the back of the product.
  5. Wait 60 seconds.
  6. Reconnect the power cord. If the product does not automatically turn on, press the Power button ( ).
  7. Reinsert the cartridges, and then close any open doors on the product.
  8. If you receive a prompt to print a calibration page, do so.
  9. Reconnect the USB cable to the rear of the product, and then try printing again.
Solution two: Service the product If you have completed all the steps listed above and are still experiencing a problem, service the product.

Posted on Nov 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code 1 mean?


Good Morning Friend,

I understand you are receiving an error code "1" on your Electrolux dishwasher. Error code "1" is a leak detector. This does not necessarily mean that there is a leak. This could be a false code. I suggest resetting your appliance, by either unplugging it or shutting the power off at the circuit breaker, for 20-30 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 19, 2014 | Electrolux Dishwashers

2 Answers

Electrolux dishwasher giving error code 1?


Good Morning Brian,

I understand that you are receiving an error code 1 on your Electrolux dishwasher, model# EWDW6505GS. Error 1 is stating that water has been detected underneath the tub. Check underneath your dishwasher by taking off the kick plate below the door. If you do not notice any water underneath the tub or any types of leaking, I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker for 20-30 minutes. When the time has passed, restore power, and run any cycle. If you are still receiving error code 1, I suggest you contact your local authorized technician for further assistance. Hope this is helpful.

-Best Regards-
WP

May 07, 2014 | Electrolux EWDW6505GS Fully Integrated...

1 Answer

Error code e000004 0401


1. Make the following selections in sequence to perform the error clear:
[Service mode > COPIER > Function > CLEAR > ERR].
2. Turn the control panel switch OFF > turn the main power switch OFF/ON.
3. If the error code still persists, check to see if the connector [1] of the fixing thermo switch is disconnected or the pin [2] of the receiving side connector is bent. If the connector is disconnected, re-fit it.

Jul 29, 2013 | Canon imageRUNNER iR C4080 Color Copier

1 Answer

THE FAX PANASONIC UF 5100 MARK EROR COD 420


The error that you are receiving means that the machine goes to receiving mode, but receives no command from the transmitting side. The problem is not with your machine, but from the party sending you the fax.
1. Remote side mis-dial.
2. Check with the other party.

Apr 11, 2012 | Office Equipment & Supplies

1 Answer

EROR 420


The error that you are receiving means that the machine goes to receiving mode, but receives no command from the transmitting side. The problem is not with your machine, but from the party sending you the fax.
1. Remote side mis-dial.
2. Check with the other party.

Apr 11, 2012 | Office Equipment & Supplies

1 Answer

Receiving a "DIC error mode


Does the printer have a suitable power source? That error usually comes up if someone attempts to tamper with the unit or power is not up to suitable standards.

Nov 01, 2010 | Ricoh SFX2000MI Plain Paper Fax

1 Answer

Error 441 seems to take all pages but receiver get aapx. 1 paragraph & the rest is blurred - same incoming


This means that an error occurred during transmission after one or more partial pages were sent. The sending machine was unable to restart the control channel connection(handshake) before sending more data. This error typically occurs when the receiving fax disconnects after receiving part of a page. It can also be caused if the receiving fax is using a fax format incompatible with the HP fax (usually during color faxing) or the line speed drops to an unacceptable level.

Solutions

Check that the phone cord is plugged in correctly and is not cut, creased or damaged.


Make sure that the phone connection terminal box is not damaged and that the cable connecting to it is not damaged.

Try the fax at a different time when telephone line conditions have improved.

Oct 08, 2009 | HP OfficeJet d145 InkJet Printer

1 Answer

I am receiving error code 39,012.40:76243 on C2424


Replace document feeder. 004k07270 $390.00

Sep 04, 2009 | Xerox C2424 Copier

1 Answer

I have a 2002 Dodge Intrepid. I received 2 error codes P0441 and P0155. I had a sensor replaced and now I am receiving 1 code a Po152. Can you please tell me what this means?


P0152 is o2 sensor 2/1 voltage high. Sensor 2/1 is your right bank upstream o2 sensor located in the manifold. Make sure it is pluged in.

Dec 26, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
HP PSC 1610 All-In-One InkJet Printer Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...