Question about JBL BP1200.1 Car Audio Amplifier

1 Answer

Jbl car amplifier

I dont know how to connect to the mono channel, because i bought it to ebay but the owner did not have the manual factory. Can you maybe send me a picture or something else please.Do you have costumer service phone number of jbl

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Hi,

you can download the manual here http://url2it.com/gme

if you need further help please reply back.

Posted on Jun 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The ampe i got is the bp1200.1 is that 1200 watts in to one chanel can you tell me thanks


it is a mono (one channel) amp. it outputs 600 watts at 4 ohms (1x4 ohm speaker connected) and 1200 watts at 2 homs (2x4ohm speakers or dual 4 ohm voice coils in parallel).

Jan 31, 2011 | JBL BP1200.1 Car Audio Amplifier

1 Answer

How do you bridge a JBL GTO7001 amp


JBL do not suggest bridging this amplifier. As it is a mono block, the "stereo outputs that are on the amplifier go to the same contacts inside", so effectively both Left and Right outputs are the same, (like using a headphone splitter.) this is designed for ease of use when installing more than one subwoofer. if you run your sub/s at two ohms you will be able to get the full 700WRMS out of this unit.
so in effect if you "bridge" this amplifier it will not be any different if you hadn't. Bridging is designed for TWO or more channel amplifiers to increase the power going to the speakers, but not needed in a mono block amplifier.
I hope i have helped you with your problem and please dont forget to rate my solution.
cheers

Jan 14, 2011 | JBL GTO7001 Car Amp

2 Answers

Jbl audio wiring diagram/schematics/color codes/ect.ect.ect.


http://documents.victorytechnologies.com//documents/product/2322.pdf

Mar 15, 2010 | JBL BP1200.1 Car Audio Amplifier

1 Answer

Bridging outputs on JBL BP300


Hello paulnkate,

The BP300.1 is a mono (1 channel) amp. You cannot bridge a mono amp. Bridging is a method of combining the outputs of 2 or more channels of a multichannel amp into a single mono load. On your amp you would connect a single sub to one of the +'s and one of the -'s (either one is OK, they are connected internally). The other pair of terminals is just for convenience, making it easier to connect, if you want to power 2 subs.

Hope this helps.

Jul 20, 2009 | JBL BP300.1 PowerValve Series Car Audio...

1 Answer

My Jbl mono amp cuts out


It's likely that the amp has blown output transistors. To eliminate other possible problems, read through the following page:

Amp Going into Protection Mode

Let me know if you have any other questions.

Sep 14, 2008 | JBL GTO75.4 Car Audio Amplifier

2 Answers

Hey thanks alot for the help, the way its hooked up now the amp eventually gets way to hot and the shut-off saftey heat switch just comes on. wondering if you had any suggestions for a good amp along with...


I would definately say, in the world of amplifiers you usually get what you pay for. I would recommend getting a Memphis or MTX amplifier. Go to ebay, specifically search for memphis then in the search options make sure to put in mono or 1 channel. All memphis mono block amps are 2 ohms stable. In particularly I would recommend for you the PR series. it is the Power reference series and they are really boomy for the money. Anything that has the "ST" is getting a little old so I wouldn't recommend it but It still is a good amp, just not sure how long it would last and how badly it's been beaten in the past. Good luck. If you find an amp and are unsure let me know which one and I can help verify it for you.
-Andrew Hawkins

Aug 30, 2008 | Legend LA1490 - American Legacy Series 2 -...

2 Answers

My tweeters do not give sound


just run the tweeters to the front speaker channels on the radio

Mar 10, 2008 | MTX Thunder 1501D Car Audio Amplifier

1 Answer

JBL Sub Amp Wiring Please


it seems rather redundant to bridge a mono amp. Unless the instruction manual states otherwise, i would assume that one speaker output is identical to the other (ran in parallel, like an A or B speaker, not like Left or Right), and you would present the amp with a two ohm load by wiring one speaker to each output. Bridging it may or may not work, but, again, it just seems redundant.

Mar 01, 2008 | Car Amplifiers

1 Answer

Jbl gto 3501 amp


It's a mono amp. There's no bridging with this amp.

The two pairs of speaker terminals are connected together internally. The second set of terminals is for convenience.

Dec 21, 2007 | JBL BP1200.1 Car Audio Amplifier

2 Answers

Clarion APA5240 5 channel Amp


try this it has worked for me in the past,..Contact Clarion by e-mail .Tell them your a student and learning electronics and in need of installation ,owners manual..ask if they can help and mail you info you need.Or try this link ..Its for a APA5241 could be very similar..http://www.clarion.com/us/en/MungoBlobs/720/1016/APA5241.pdf

Dec 14, 2007 | Car Amplifiers

Not finding what you are looking for?
JBL BP1200.1 Car Audio Amplifier Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top JBL Car Amplifiers Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Sudeep Chatterjee
Sudeep Chatterjee

Level 3 Expert

3267 Answers

Are you a JBL Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...