Question about Toshiba TEC B-572 Printer

1 Answer

Toshiba TEC B-572 Printer

I cannot get the printer to print.I have tried adjusting the sensor.the massage is either PAPER JAM or NO PAPER, I am using plastic stick-in labels which are 'notched' on the left hand side, looking from the front of the machine, I have been using this machine for several years.Can you help?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 254 Answers

You should recalibrate your sensor without or use reflective sensor instead of transmissive.

Posted on Sep 03, 2009

  • pkwc Sep 03, 2009

    You should recalibrate your sensor without or use reflective sensor instead of transmissive.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ribbon error /paper jam

probaly due to a wrong mounting of the labels and the transfer films

Nov 05, 2013 | Toshiba TEC B-572 Printer

1 Answer

Paper jam in Toshiba Tec

Check length of label and type of sensor used and check the sensors

Apr 02, 2013 | Toshiba TEC B-472 Thermal Label Printer

1 Answer

I keep getting a Paper Jam message even after calibrating many times. Am using continuous roll of 1 X 4 lables. Was working fine until I tried to print another set of lables. What Gives? Am using a...

2 x possibilities.

1. sensor may need moving to to see label edge (green knob at RHS)

2. possible sensor faulty. Only testable by substitution.

Jul 06, 2011 | Toshiba TEC B-572 Printer

1 Answer

Receiving error "No Paper" but there are labels loaded

Have to callaibrate the sensors or you have a problem with the size of your label. The gag is in the sensor when printing starts or stops.
Use the tear option to try to correct this error or use a longer or shorter label.

Sep 10, 2010 | Toshiba TEC B-572 Printer

1 Answer

TEC B-572 printer, labels off center.

Check the alignement of the media guide. and the alignement of the print head. + X adjust parameter

May 15, 2010 | Toshiba TEC B-572 Printer

1 Answer

I am getting paper jam i did follow all the instractions but nothing help what can i do?

Various reasons for paper jam.
In peel off mode the paper is not detected after printing.
- recalibrate the sensors.
- Preprint callibration.
- Sensors do not conform to your CPU release.

Aug 26, 2009 | Toshiba TEC B-572 Printer

1 Answer

Tec 572 printer gives "no ribbon" error with ribbon installed

You have to set the ribbon type to be "non-transmissive" for black transfer film.
To set the ribbon type, turn the printer off. Then press and hold the "feed" and "pause" buttons while turning on the power. The printer will now be in diagnostic mode - you can page through the menus until it says "ribbon type"
Pick the correct type and press the "pause" key to save the value. Then turn off the printer and turn it on again normally. The ribbon error goes away.

Mar 19, 2009 | Toshiba TEC B-572 Printer

1 Answer

Print jam on the thermal TEC B-572 TXP -3.5

The purpose of the knob if to change the position of the sensor. If you look at the sensor when turning the knob you'll find out that it moves forward (towards you) or backwards (away from you) This should allow you to place the sensor at the correct position. Further more, there are two holes on the plastic flag. the hole nearer to you is the transmissive sensor and the other is for reflective. Try to place the sensor at the correct position.

Mar 25, 2008 | Toshiba TEC B-572 Printer

Not finding what you are looking for?
Toshiba TEC B-572 Printer Logo

Related Topics:

844 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba TEC Office Equipment & Supplies Experts


Level 3 Expert

1121 Answers


Level 3 Expert

12962 Answers


Level 3 Expert

102366 Answers

Are you a Toshiba TEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides